Pinouts & Pin References
for ICs & Semiconductors.

Pinout diagrams for timers, op-amps, logic gates, voltage regulators, and driver ICs.

377+ components available

All Boards, Chips & Connectors

Development platforms, microcontrollers, ICs and standard interfaces

Chip
Microchip

MCP2221A USB-to-UART/I2C Converter

USB-to-UART serial converter with I2C master, four multifunction GP pins (GPIO, ADC, DAC, clock, LED), integrated USB termination and oscillator. Supply 3.3V USB.

Chip
Microchip

MCP2518FD CAN FD Controller with SPI Interface

External CAN FD controller with SPI interface, TXCAN/RXCAN to transceiver, oscillator pins, two interrupt/GPIO pins and CLKO/SOF output.

Chip
Microchip

MCP2562 CAN Transceiver

CAN transceiver with permanent dominant detection, VDD and VIO undervoltage detection, Standby mode input, and separate VIO supply for RXD (MCP2562 variant).

Chip
Microchip

MCP73831 Li-Ion Battery Charge Controller

Single-cell Li-Ion/Li-Po battery management controller with constant current/constant voltage charging, programmable charge current via PROG resistor, and charge status output.

Chip
Microchip

MCP7940N Real-Time Clock/Calendar with SRAM

I2C real-time clock/calendar with SRAM and battery backup input. Uses external 32.768 kHz crystal (6-9 pF load). Open-drain SDA and multifunction MFP outputs.

Chip
Microchip

MCP79410 I2C Real-Time Clock/Calendar with SRAM

I2C real-time clock/calendar (RTCC) with battery backup input and SRAM, driven by an external 32.768 kHz crystal. Pin-compatible family members MCP79411 and MCP79412.

Chip
Monolithic Power Systems

MP2307DN-LF-Z 3A 23V synchronous step-down converter

3A, 23V input, 340kHz synchronous rectified step-down converter with current-mode control, internal MOSFETs, soft-start and 0.925V feedback reference.

Chip
Macronix

MX25L6433F Serial Flash Memory

64M-bit serial Flash memory with SPI, dual I/O and quad I/O support, +3.0V supply. Pin list from the 8-pin SOP (200mil) package in the datasheet.

Chip
onsemi

NCP1117ST33T3G 3.3V 1.0A Low-Dropout Positive Voltage Regulator

1.0 A low-dropout positive fixed 3.3 V regulator, up to 20 V input, current limit and thermal shutdown. SOT-223, heatsink tab connected to Output pin 2.

Chip
ON Semiconductor

NCV7692 Current Controller for Automotive LED Lamps

Constant-current LED driver controller using an external NPN transistor and feedback resistor. PWM dimming, open LED and short-circuit diagnostics, NTC option, overvoltage setback. AEC-Q100.

Chip
onsemi

NL17SZ08 Single 2-Input AND Gate

Single 2-input AND gate, Y = A AND B. VCC 1.65 V to 5.5 V, 2.7 ns tPD at 5 V. Inputs and outputs overvoltage tolerant to 5.5 V, IOFF partial power down support.

Chip
Nordic Semiconductor

NRF52820 Bluetooth Low Energy SoC

Nordic nRF52820 BLE SoC pinout: 32 MHz and 32.768 kHz crystal inputs, USB 2.0 D+/D-, 5 V VBUS input, DC/DC output, SWD debug, GPIO and analog inputs.

Chip
Nordic Semiconductor

NRF52832-QFAA-R Bluetooth SoC

nRF52832 ARM Cortex-M4F SoC with BLE radio, 512 kB flash, 64 kB RAM, 32 MHz and 32.768 kHz crystal inputs, SAADC, NFC and SWD debug. QFN48 6x6 mm package.

Chip
Nordic Semiconductor

NRF52833 QIAA-R Bluetooth SoC pinout

nRF52833 multiprotocol SoC with Arm Cortex-M4F, BLE 5, NFC, USB and 1.1/1.3 V regulators. QFN40 5x5mm pin assignment table.

Chip
Nordic Semiconductor

NRF52840-QIAA-R Bluetooth 5 / multiprotocol SoC with ARM Cortex-M4F

Nordic nRF52840 BLE/NFC/Thread/Zigbee/ANT SoC, ARM Cortex-M4F 64 MHz, 1 MB flash, 256 KB RAM, USB, QSPI, aQFN73 7x7mm package pinout.

Frequently Asked Questions & Transparency

Helpful information about data sources, usage, and privacy

Where does the pinout data and technical specification come from?

The pinout data and technical specifications are based on official manufacturer datasheets as well as publicly available documentation and community resources. As PinoutDatabase is an independent project maintained by me as an individual, I strive for high accuracy, though inadvertent mistakes can still happen.

Can I use the graphics and how are they created?

The SVG vector files and PNG graphics are free to download and use for private/personal purposes. Depending on the component, the diagrams are either crafted manually or generated automatically based on package footprint and pin definitions.

Found an error or missing a component? How can I give feedback?

Community feedback is always appreciated! If you spot an error or are missing a specific component, please use the 'Report Issue' button directly on that component's page or send me a message via the contact form.

Is the site free to use and how is privacy handled?

Currently, using PinoutDatabase is completely free and requires no registration. All interactive web tools run entirely client-side inside your browser. Detailed information regarding data processing can be found directly on our Privacy Policy page.