Pinouts & Pin References
for ICs & Semiconductors.

Pinout diagrams for timers, op-amps, logic gates, voltage regulators, and driver ICs.

377+ components available

All Boards, Chips & Connectors

Development platforms, microcontrollers, ICs and standard interfaces

Chip
Renesas

ISL78420 Tri-level PWM high/low-side MOSFET gate driver

Synchronous high/low-side NMOS gate driver with tri-level PWM input, adjustable dead time via RDT, bootstrap diode, and VDD/VHB undervoltage protection. -40 to +125C.

Chip
Texas Instruments

ISO1050 isolated CAN transceiver

Isolated CAN transceiver with digital-side VCC1 (3 to 5.5 V) and transceiver-side VCC2 (5 V), CAN bus lines CANH/CANL, and separate GND1/GND2 references. DUB 8-pin package.

Chip
Texas Instruments

LM2675M-5.0 Simple Switcher 1A Step-Down Voltage Regulator

1A step-down (buck) switching voltage regulator with internal high-side FET, 5.0 V fixed output option, boot-strap capacitor input, feedback pin, and ON/OFF enable. Supply range 6.5 V to 40 V.

Chip
Texas Instruments

LM2940IMP-5.0/NOPB 1-A Low Dropout Linear Regulator

1-A positive low dropout linear regulator, 6 V to 26 V input, typical dropout 0.5 V at 1 A, reverse battery protection, short circuit and thermal overload protection.

Chip
Texas Instruments

LP5009 9-channel I2C RGB LED driver

9-channel constant-current sink LED driver with 12-bit 29-kHz PWM per channel, I2C interface, VCC 2.7-5.5 V, up to 35 mA per channel, integrated color mixing and brightness control.

Chip
NXP

LPC1114FBD48/302 32-bit ARM Cortex-M0 microcontroller

32-bit ARM Cortex-M0 MCU, LQFP48 pinout from LPC1113/14 table. GPIO ports 0-3, UART, SPI, I2C, 16/32-bit timers, ADC inputs, JTAG/SWD debug, 3.3 V supply.

Chip
NXP

LPC812M101JDH20 32-bit ARM Cortex-M0+ microcontroller

NXP LPC81xM 32-bit ARM Cortex-M0+ MCU, TSSOP20 package. GPIO, USART, SPI, I2C, SCT, analog comparator, on-chip oscillator, 3.3 V supply.

Chip
Analog Devices

LT3045 Ultralow Noise 500mA LDO Regulator

Ultralow noise, high PSRR 500mA linear regulator with programmable output via SET pin, current limit via ILIM, power good via PG/PGFB, and EN/UV enable. Input 2V to 20V, output 0V to 15V.

Chip
Analog Devices

LT3080 Linear Regulator

Linear regulator with VCONTROL, IN, OUT and SET pins. Absolute max 40V on VCONTROL and IN, Tjmax 125C, indefinite output short-circuit duration. Pin 9 exposed pad is OUT.

Chip
Analog Devices

LTC3622 Dual Step-Down Regulator

Dual synchronous step-down DC/DC regulator with Burst Mode/pulse-skip control, external sync, 180 degree phase select, programmable current limit, and INTVCC LDO. 14-lead DFN.

Chip
Maxim Integrated

MAX17055 1-Cell Fuel Gauge with ModelGauge m5 EZ

7uA 1-cell battery fuel gauge with ModelGauge m5 EZ algorithm, I2C/SMBus-style 2-wire serial interface, ALRT open-drain alert, thermistor bias input and Kelvin sense resistor pins.

Chip
RAMXEED (Fujitsu)

MB85RS64V Serial FeRAM Memory with SPI Interface

Serial FeRAM memory with SPI-compatible interface (CS, SCK, SI, SO), write protect and hold pins. 8-pin plastic SOP 150mil package.

Chip
onsemi

MC74HC595A 8-Bit Shift Register with Latch

8-bit serial-in, parallel-out shift register with storage latch and tri-state outputs. Serial data output SQH for cascading. Logic supply VCC on pin 16, GND on pin 8.

Chip
Microchip

MCP1700 Low Dropout Linear Voltage Regulator

Low dropout linear regulator with 3.3V fixed output (MCP1700T-3302E/TT). Typical 1.6 uA LDO bias current. Requires about 1 uF input capacitance for stable operation.

Chip
Microchip

MCP2003B LIN Transceiver

LIN bus transceiver with open-drain RXD, TTL TXD and CS inputs, HV-tolerant wake-up input, and VREN regulator enable output. Battery-referenced VBB supply, SOIC-8 package.

Frequently Asked Questions & Transparency

Helpful information about data sources, usage, and privacy

Where does the pinout data and technical specification come from?

The pinout data and technical specifications are based on official manufacturer datasheets as well as publicly available documentation and community resources. As PinoutDatabase is an independent project maintained by me as an individual, I strive for high accuracy, though inadvertent mistakes can still happen.

Can I use the graphics and how are they created?

The SVG vector files and PNG graphics are free to download and use for private/personal purposes. Depending on the component, the diagrams are either crafted manually or generated automatically based on package footprint and pin definitions.

Found an error or missing a component? How can I give feedback?

Community feedback is always appreciated! If you spot an error or are missing a specific component, please use the 'Report Issue' button directly on that component's page or send me a message via the contact form.

Is the site free to use and how is privacy handled?

Currently, using PinoutDatabase is completely free and requires no registration. All interactive web tools run entirely client-side inside your browser. Detailed information regarding data processing can be found directly on our Privacy Policy page.