Pinouts & Pin References
for ICs & Semiconductors.
Pinout diagrams for timers, op-amps, logic gates, voltage regulators, and driver ICs.
All Boards, Chips & Connectors
Development platforms, microcontrollers, ICs and standard interfaces
MCP4725 12-Bit DAC with I2C Interface and EEPROM
Low-power, high accuracy, single channel, 12-bit voltage output Digital-to-Analog Converter (DAC) with integrated non-volatile EEPROM and 2-wire I2C interface. Stores power-on reset output settings directly in on-board EEPROM.
TXS0108E 8-Bit Bidirectional Voltage-Level Translator
8-bit non-inverting bidirectional logic voltage level translator with automatic direction sensing and output enable (OE). Allows seamless communication between mixed-voltage systems (e.g. 1.8V/3.3V microcontrollers and 5V sensors/peripherals) across high-speed I2C, SPI, and UART buses.
MCP4921 12-Bit DAC with SPI Interface
Single-channel 12-bit Digital-to-Analog Converter (DAC) with an internal output amplifier and high-speed SPI serial interface (up to 20 MHz). Features user-selectable gain (1x or 2x) and selectable external voltage reference input.
Macronix MX25L25645G (SOP-16)
3V 256M-bit (32M-byte) CMOS MXSMIO Multi-I/O Serial NOR Flash in 16-pin SOP 300-mil package. Features a dedicated hardware RESET# input on Pin 3 and NC/SIO3 on Pin 1.
Macronix MX25L25645G (SOP-8 / WSON-8)
3V 256M-bit (32M-byte) CMOS MXSMIO Multi-I/O Serial NOR Flash in 8-pin SOP 200-mil and 8-land WSON packages. Supports Single/Dual/Quad I/O, QPI, DTR mode up to 133MHz, JEDEC ID C2h 2019h.
PT2399 CMOS Echo / Delay Audio Processor
Single-chip CMOS echo and audio delay processor utilizing internal 44Kbit digital RAM with integrated ADC, DAC, and operational amplifiers. Widely used in guitar pedals, synthesizers, and karaoke equipment.
Winbond W25Q128JWF (SOIC-16)
1.8V 128M-bit (16M-byte) Serial NOR Flash memory with Dual/Quad SPI in 16-pin SOIC 300-mil package. Standard IQ series with factory-fixed Quad Enable (QE=1), dedicated hardware /RESET pin on Pin 3, and JEDEC ID 6018h.
Winbond W25Q128JWS (SOIC-8 / WSON-8)
1.8V 128M-bit (16M-byte) Serial NOR Flash memory with Dual/Quad SPI in 8-pin SOIC 208-mil and 8-pad WSON packages. Standard IQ series with factory-fixed Quad Enable (QE=1) and JEDEC ID 6018h.
Winbond W25Q256JW (WSON-8)
1.8V 256M-bit (32M-byte) Serial NOR Flash memory with Dual/Quad SPI in 8-pad WSON package (6x5mm / 8x6mm). Standard IQ series with factory-fixed Quad Enable (QE=1) and JEDEC ID 6019h.
Winbond W25Q256JWF (SOIC-16)
1.8V 256M-bit (32M-byte) Serial NOR Flash memory with Dual/Quad SPI in 16-pin SOIC 300-mil package. Standard IQ series with factory-fixed Quad Enable (QE=1), dedicated hardware /RESET input (Pin 3), and JEDEC ID 6019h.
MAX3232 3.0V-5.5V Dual RS-232 Transceiver
Two-channel line driver and receiver with ±15-kV ESD protection and internal charge pump for 3.0V to 5.5V operation. Meets EIA/TIA-232-F standards while operating directly from 3.3V microcontroller logic without external high voltage supplies.
SN754410 Quadruple Half-H Motor Driver
Quadruple high-current half-H driver designed to provide bidirectional drive currents of up to 1A at voltages from 4.5V to 36V. Pin-compatible higher-current modern alternative to the popular L293D with internal output clamp diodes for inductive transient suppression.
74HC4052 Dual 4-Channel Analog Multiplexer / Demultiplexer
Dual 4-channel analog multiplexer/demultiplexer with common channel select logic and active-low enable. Supports bidirectional signal routing of digital and analog voltages up to 10V with low ON resistance and break-before-make switching.
74HC4053 Triple 2-Channel Analog Multiplexer / Demultiplexer
Triple 2-channel analog multiplexer/demultiplexer (three independent SPDT analog switches) with three separate digital select inputs and a common enable input. Designed for analog and digital signal switching up to 10V peak-to-peak.
74HC151 8-Input Data Selector / Multiplexer
High-speed silicon-gate CMOS 8-channel data selector/multiplexer. Decodes 3 binary address inputs (S0, S1, S2) to select one of eight data sources (D0 through D7) with complementary true (Y) and inverted (~W) outputs.
Frequently Asked Questions & Transparency
Helpful information about data sources, usage, and privacy
Where does the pinout data and technical specification come from?
The pinout data and technical specifications are based on official manufacturer datasheets as well as publicly available documentation and community resources. As PinoutDatabase is an independent project maintained by me as an individual, I strive for high accuracy, though inadvertent mistakes can still happen.
Can I use the graphics and how are they created?
The SVG vector files and PNG graphics are free to download and use for private/personal purposes. Depending on the component, the diagrams are either crafted manually or generated automatically based on package footprint and pin definitions.
Found an error or missing a component? How can I give feedback?
Community feedback is always appreciated! If you spot an error or are missing a specific component, please use the 'Report Issue' button directly on that component's page or send me a message via the contact form.
Is the site free to use and how is privacy handled?
Currently, using PinoutDatabase is completely free and requires no registration. All interactive web tools run entirely client-side inside your browser. Detailed information regarding data processing can be found directly on our Privacy Policy page.