Pinouts & Pin References
for ICs & Semiconductors.

Pinout diagrams for timers, op-amps, logic gates, voltage regulators, and driver ICs.

377+ components available

All Boards, Chips & Connectors

Development platforms, microcontrollers, ICs and standard interfaces

Chip
Silicon Labs

CP2104-F03-GMR USB to UART Bridge Controller

USB to UART bridge controller with integrated 5 V regulator, VBUS sense, 4 GPIO, and full RS-232 style modem control signals (RTS/CTS/DTR/DSR/DCD/RI). QFN-24 package.

Chip
Texas Instruments

DAC8563SDGSR Dual 16-Bit Buffered Voltage-Output DAC

Dual-channel 16-bit low-power buffered voltage-output DAC with 2.5-V 4-ppm/C internal reference, 50-MHz three-wire SPI interface, rail-to-rail output, 2.7 V to 5.5 V supply.

Chip
Diodes Inc

DGD2136M28-13 3-phase high-voltage gate driver

3-phase high-side/low-side MOSFET/IGBT gate driver, floating high-side supplies up to 600V, overcurrent ITRIP shutdown, fault output and RCIN fault clear delay.

Chip
Silicon Labs

EFR32BG22C224F512GM32-C Wireless Gecko Bluetooth SoC

EFR32BG22 Wireless Gecko 2.4 GHz Bluetooth SoC, 512 kB flash, QFN32 5x5 mm, with DCDC regulator and GPIO ports A, B, C and D.

Chip
Espressif

ESP32-C3FH4 Wi-Fi/BLE SoC

RISC-V Wi-Fi and Bluetooth LE SoC with in-package flash. QFN32 5x5mm pinout with IO MUX (F0-F2) and GPIO Matrix peripheral routing.

Chip
Espressif

ESP32-C6FH4 Wi-Fi 6 BLE SoC

ESP32-C6 series Wi-Fi 6, Bluetooth LE and 802.15.4 SoC. QFN40 5x5mm pinout with IO MUX, GPIO matrix and peripheral pin assignment.

Chip
Espressif

ESP32-D0WD-V3 Wi-Fi/BT SoC

Espressif ESP32 dual-core Wi-Fi/Bluetooth SoC in QFN48 5x5mm. Provides GPIO matrix, ADC, DAC, touch, SD/SDIO, Ethernet MAC, UART and SPI/I2S pins.

Chip
Espressif

ESP32-S2FH4 Wi-Fi MCU

ESP32-S2 series Wi-Fi MCU in QFN56 7x7mm: GPIO matrix, ADC, DAC, touch, USB OTG, SPI, UART, I2C, I2S, TWAI, LEDC, JTAG. Exposed ground pad 57.

Chip
Espressif

ESP32-S3FN8 Wi-Fi/BLE SoC

ESP32-S3 dual-core Wi-Fi and Bluetooth LE SoC with GPIO matrix, IO MUX, RTC IO, SPI flash interface, USB and JTAG, in QFN56 7x7mm package.

Chip
FTDI

FT2232HL Dual High Speed USB to Multipurpose UART/FIFO

Dual-channel high speed USB to multipurpose UART/FIFO IC with RS232 UART, FT245 FIFO, bit-bang, MPSSE and CPU-style FIFO modes. 64-pin LQFP package.

Chip
FTDI

FT230XS-R USB to Basic UART IC

USB to basic UART bridge IC in 16-pin SSOP. VCC 5V or 3V3, VCCIO 1V8-3V3 for IO, 3V3 output at 50mA, reset and configurable CBUS I/O pins.

Chip
Texas Instruments

INA128UA Precision Instrumentation Amplifier

Precision low-power instrumentation amplifier with 50uV max offset, 0.5uV/C max drift, 120dB min CMR, gain 1 to 10000 set by external RG, supply +/-2.25V to +/-18V.

Chip
Texas Instruments

INA3221AIRGVR Triple-Channel Current and Bus Voltage Monitor

Three-channel high-side current and bus voltage monitor with I2C/SMBus interface, 13-bit ADC, 0-26V bus range, 2.7-5.5V supply, critical/warning/PV/TC alert outputs, -40 to +125 C.

Chip
Texas Instruments

INA333 Micro-Power Zero-Drift Rail-to-Rail Instrumentation Amplifier

Micro-power (50 uA) zero-drift rail-to-rail instrumentation amplifier, 1.8 V to 5.5 V supply, gain 1 to 1000 set by external RG (G = 1 + 100k/RG), RFI filtered inputs.

Chip
Infineon

IR2104STRPBF High-Side/Low-Side Half-Bridge Gate Driver

High voltage, high speed half-bridge driver for N-channel MOSFET/IGBT. Floating high side rated to 600V, 10-20V gate supply, 130/270 mA peak output current, internal deadtime, SOIC-8.

Frequently Asked Questions & Transparency

Helpful information about data sources, usage, and privacy

Where does the pinout data and technical specification come from?

The pinout data and technical specifications are based on official manufacturer datasheets as well as publicly available documentation and community resources. As PinoutDatabase is an independent project maintained by me as an individual, I strive for high accuracy, though inadvertent mistakes can still happen.

Can I use the graphics and how are they created?

The SVG vector files and PNG graphics are free to download and use for private/personal purposes. Depending on the component, the diagrams are either crafted manually or generated automatically based on package footprint and pin definitions.

Found an error or missing a component? How can I give feedback?

Community feedback is always appreciated! If you spot an error or are missing a specific component, please use the 'Report Issue' button directly on that component's page or send me a message via the contact form.

Is the site free to use and how is privacy handled?

Currently, using PinoutDatabase is completely free and requires no registration. All interactive web tools run entirely client-side inside your browser. Detailed information regarding data processing can be found directly on our Privacy Policy page.