Pinouts & Pin References
for ICs & Semiconductors.

Pinout diagrams for timers, op-amps, logic gates, voltage regulators, and driver ICs.

377+ components available

All Boards, Chips & Connectors

Development platforms, microcontrollers, ICs and standard interfaces

Chip
Analog Devices

ADG1408 8:1 analog multiplexer

ADG1408 8-channel analog multiplexer, single drain D, 3-bit address A0-A2 with active high enable EN, dual or single supply operation (VSS/VDD).

Chip
Analog Devices

ADM3053 Isolated CAN Transceiver

Isolated CAN transceiver with iCoupler data isolation and isoPower isolated DC-DC supply. Slope control on RS; standby when RS is high. 20 pins.

Chip
Texas Instruments

ADS1220 24-bit 2-kSPS 4-channel delta-sigma ADC with PGA

24-bit, 2 kSPS, 4-channel delta-sigma ADC with low-noise PGA (gain up to 128), SPI interface, excitation current sources, temperature sensor and internal/external clock.

Chip
Texas Instruments

ADS131M04 4-Channel Delta-Sigma ADC

4-channel analog-to-digital converter with differential analog inputs, serial data interface (SCLK, DIN, DOUT, CS, DRDY), master clock input, and on-chip digital LDO.

Chip
Analog Devices

ADuM1200/ADuM1201 Digital Isolator

Dual-channel digital isolator with reinforced insulation rated 560 VPEAK per IEC 60747-17. Ambient range -40C to +105C, or -40C to +125C for W automotive grades.

Chip
Diodes Inc

AP22802AW5-7 Current-Limited Power Switch

Current-limited load switch with over-current and over-temperature fault flag (open-drain, active low), enable input, SOT-25 package. Not recommended for new design.

Chip
Diodes Inc

AP63203WU-7 3.8V-32V 2A Synchronous Buck Converter

2A synchronous step-down DC/DC buck converter, 3.8V to 32V input, 0.8V +/-1% feedback, integrated 125mOhm high-side and 68mOhm low-side MOSFETs, 1.1MHz, peak current mode control, spread spectrum EMI reduction.

Chip
Diodes Inc

AP7361C 1A Low Dropout Adjustable/Fixed Regulator with Enable

1A low dropout linear regulator with enable, adjustable or fixed output (0.8V to 5.0V adjustable), 2.2V to 6.0V input, 60uA typical quiescent current, 1.5A current limit, thermal shutdown.

Chip
Microchip

AT24C256C I2C Serial EEPROM 256Kbit

256-Kbit two-wire serial EEPROM, 32,768 x 8, I2C interface, 1.7V to 5.5V (Grade 3) or 2.5V to 5.5V (Grade 1), hardware write-protect, 3 address inputs.

Chip
Microchip

ATtiny1614 8-bit AVR microcontroller

8-bit AVR MCU with 16KB Flash, 2KB SRAM, 256B EEPROM, GPIO on VDD power domain, UPDI programming, crystal and external clock inputs. SOIC-14 package.

Chip
Texas Instruments

BQ25895RTWR I2C Single-Cell Li-Ion Battery Charger with Boost

I2C-controlled single-cell Li-ion charger with USB input, MaxCharge D+/D- adapter support, ICO, and 4.5-5.5 V battery boost on PMID up to 3.1 A. WQFN-24 with PowerPAD.

Chip
onsemi

CAT4101 1 A Constant-Current LED Driver with PWM Dimming

1 A constant-current LED sink, 0.5 V dropout at 1 A, LED current set by RSET resistor, PWM dimming via EN/PWM, LED pin up to 25 V, thermal shutdown.

Chip
WCH

CH340C USB to serial UART bridge

USB to UART bridge with MODEM control signals (RTS#, DTR#, DSR#, DCD#, RI#, CTS#), built-in oscillator interface, 3.3V/5V supply options, SOP-16 package.

Chip
WCH

CH9102F USB-to-UART Bridge

USB 2.0 full-speed to UART bridge with modem control signals and GPIOs. QFN-24 4x4mm package, 0.5mm pitch, backplane pad listed as pin 0.

Chip
Silicon Labs

CP2102N USB-to-UART Bridge Controller

Silicon Labs USB-to-UART bridge with USB 2.0 full-speed interface, UART flow control, GPIO, USB charger control and suspend outputs. QFN28 pinout.

Frequently Asked Questions & Transparency

Helpful information about data sources, usage, and privacy

Where does the pinout data and technical specification come from?

The pinout data and technical specifications are based on official manufacturer datasheets as well as publicly available documentation and community resources. As PinoutDatabase is an independent project maintained by me as an individual, I strive for high accuracy, though inadvertent mistakes can still happen.

Can I use the graphics and how are they created?

The SVG vector files and PNG graphics are free to download and use for private/personal purposes. Depending on the component, the diagrams are either crafted manually or generated automatically based on package footprint and pin definitions.

Found an error or missing a component? How can I give feedback?

Community feedback is always appreciated! If you spot an error or are missing a specific component, please use the 'Report Issue' button directly on that component's page or send me a message via the contact form.

Is the site free to use and how is privacy handled?

Currently, using PinoutDatabase is completely free and requires no registration. All interactive web tools run entirely client-side inside your browser. Detailed information regarding data processing can be found directly on our Privacy Policy page.