Pinouts & Pin References
for ICs & Semiconductors.

Pinout diagrams for timers, op-amps, logic gates, voltage regulators, and driver ICs.

377+ components available

All Boards, Chips & Connectors

Development platforms, microcontrollers, ICs and standard interfaces

Chip
Texas Instruments

OPA1612 Dual SoundPlus Audio Op Amp

Dual bipolar-input audio op amp. 1.1 nV/sqrt(Hz) noise at 1 kHz, 0.000015% THD+N at 1 kHz, 27 V/us slew rate, 40 MHz bandwidth at G=+1, +-2.25 V to +-18 V supply.

Chip
Texas Instruments

OPA2340UA Dual Rail-to-Rail Operational Amplifier

Dual single-supply rail-to-rail CMOS op amp. 5.5 MHz bandwidth, 6 V/us slew rate, 750 uA/channel quiescent current, 2.7 V to 5.5 V supply, -40 to 125 C specified range.

Chip
Diodes Inc.

PI4ULS3V204 4-bit Bidirectional Level Translator

4-bit bidirectional voltage level translator. VCCA and VCCB each 1.1 V to 3.6 V. Active-high output enable EN; low places all outputs in 3-state.

Chip
Texas Instruments

SN65HVD230 CAN Transceiver

3.3V CAN transceiver with RS mode select (high speed, low power, slope control) and VCC/2 Vref output. Pin 5 and 8 differ on HVD232 (NC).

Chip
Texas Instruments

SN74AHC1G04 Single Inverter Gate

Single inverter gate, AHC CMOS logic, VCC 2 V to 5.5 V, input A, output Y. Pins 1 NC, 2 A, 3 GND, 4 Y, 5 VCC in DBV (SOT-23-5) package.

Chip
Texas Instruments

SN74LVC1G08 Single 2-Input Positive-AND Gate

Single 2-input positive-AND gate, Y = A AND B. Supports 5V VCC, inputs tolerant to 5.5V, 3.6ns tpd at 3.3V, 10uA max ICC, ±24mA output drive at 3.3V.

Chip
Texas Instruments

SN74LVC8T245PWR 8-bit Dual-Supply Bus Transceiver

8-bit noninverting dual-supply bus transceiver with direction control and output enable. VCCA and VCCB 1.65V to 5.5V. 3-state outputs.

Chip
STMicroelectronics

STM32C011F6U6 Arm Cortex-M0+ MCU

Arm Cortex-M0+ 32-bit microcontroller, STM32C011x4/x6 family. Up to 5 V tolerant FT I/Os with ADC, timer, USART, SPI, I2C and SWD alternate functions. UFQFPN20 package.

Chip
STMicroelectronics

STSPIN220 Stepper motor driver with microstep control

Stepper motor driver with integrated power bridges, PWM current control, step/mode selection, enable and open-drain fault output, low-consumption standby. QFN-16 3x3 mm, exposed pad to GND.

Chip
Silicon Labs

Si4432-B1-FMR EZRadioPRO FSK/OOK transceiver

EZRadioPRO FSK/OOK transceiver with SPI control, 30 MHz crystal oscillator interface, GPIOs, interrupt output and integrated 1.7 V regulators.

Chip
Silicon Labs

Si4463-C2A-GM ISM Sub-GHz Transceiver

Sub-GHz ISM transceiver with differential RF LNA input, open-drain PA output, 4-line serial interface, GPIOs, nIRQ and 25-32 MHz crystal oscillator interface.

Chip
Texas Instruments

TCA9534 8-bit I2C-bus and SMBus I/O expander

Low-voltage 8-bit I2C/SMBus I/O expander with interrupt output, 3 address pins and push-pull P-port I/O, 16-pin TSSOP package.

Chip
Texas Instruments

THS3001 420MHz High-Speed Current-Feedback Amplifier

High-speed current-feedback op amp: 420MHz bandwidth (G=1, -3dB), 6500V/us slew rate, 40ns settling to 0.1%, 100mA output drive, +/-4.5V to +/-16V supply, -96dBc THD at 1MHz.

Chip
Texas Instruments

THS4531A Ultra Low-Power Rail-to-Rail Output Fully Differential Amplifier

Ultra low-power (250 uA) fully differential amplifier with rail-to-rail output, negative rail input, 36 MHz bandwidth, 200 V/us slew rate, 2.5 V to 5.5 V single supply, and output common-mode control.

Chip
Texas Instruments

TLC59116 16-Channel FM+ I2C-Bus Constant-Current LED Sink Driver

16-channel I2C LED sink driver, 97-kHz 8-bit PWM per output, 190-Hz group PWM, 5-120 mA constant current set by REXT, 17 V output tolerance, 3-5.5 V supply.

Frequently Asked Questions & Transparency

Helpful information about data sources, usage, and privacy

Where does the pinout data and technical specification come from?

The pinout data and technical specifications are based on official manufacturer datasheets as well as publicly available documentation and community resources. As PinoutDatabase is an independent project maintained by me as an individual, I strive for high accuracy, though inadvertent mistakes can still happen.

Can I use the graphics and how are they created?

The SVG vector files and PNG graphics are free to download and use for private/personal purposes. Depending on the component, the diagrams are either crafted manually or generated automatically based on package footprint and pin definitions.

Found an error or missing a component? How can I give feedback?

Community feedback is always appreciated! If you spot an error or are missing a specific component, please use the 'Report Issue' button directly on that component's page or send me a message via the contact form.

Is the site free to use and how is privacy handled?

Currently, using PinoutDatabase is completely free and requires no registration. All interactive web tools run entirely client-side inside your browser. Detailed information regarding data processing can be found directly on our Privacy Policy page.