USB-to-UART Bridges: CH340, CP2102 and FT232 Pinouts
The chips that connect Arduino clones, ESP boards and programming adapters to a computer.
A USB-to-UART bridge translates between a computer's USB port and a microcontroller's serial port. It sits on almost every development board: the CH340 on low-cost Arduino Nano clones and NodeMCU boards, the CP2102 on many ESP32 boards, and the FT232RL on FTDI adapters and older Arduinos. To the computer, the chip appears as a virtual COM port.
All bridges share the same basic signals: D+ and D− to the USB connector, TXD and RXD to the microcontroller, and usually RTS, CTS, DTR and DSR for flow control. DTR plays a special role, because it resets the Arduino through a capacitor so the bootloader accepts new firmware. ESP boards also use DTR and RTS to put the chip into download mode.
The differences lie in the supply: the CH340G needs an external 12 MHz crystal, while the CH340C, CP2102N and FT232RL have the clock built in. Some types provide 3.3 V on one pin for the rest of the circuit. The table shows the package, supply pins and interfaces of every bridge.
Overview from the pinout data
| Part | Manufacturer | Package | Pins | Supply | Interfaces |
|---|---|---|---|---|---|
| CH340G USB to Serial UART Bridge Controller | WCH (Jiangsu Qinheng) | 16-Pin DIP / SOIC | 16 | VCC 4, 16GND 1 | UARTUSB |
| CH340C USB to serial UART bridge | WCH | 16-Pin DIP / SOIC | 16 | VCC 4, 16GND 1 | – |
| CH9102F USB-to-UART Bridge | WCH | QFP / QFN | 25 | VCC 6, 7GND 0, 2 | – |
| CP2102N USB-to-UART Bridge Controller | Silicon Labs | QFP / QFN | 29 | VCC 6GND 3, EP | – |
| CP2102N USB to UART Bridge Controller | Silicon Labs | QFP / QFN | 25 | VCC 6GND 2, 25 | UARTUSB |
| CP2104-F03-GMR USB to UART Bridge Controller | Silicon Labs | QFP / QFN | 24 | VCC 6GND 2 | – |
| FT232RL USB to Serial UART Interface IC | FTDI Chip | 26-Pin DIP / SOIC | 26 | VCC 20GND 7, 18, 21 | UARTUSB |
| FT230XS-R USB to Basic UART IC | FTDI | 16-Pin DIP / SOIC | 16 | VCC 12GND 5, 13 | – |
| FT2232HL Dual High Speed USB to Multipurpose UART/FIFO | FTDI | QFP / QFN | 64 | GND 1, 5, 10 | – |
| MCP2221A USB-to-UART/I2C Converter | Microchip | 14-Pin DIP / SOIC | 14 | VCC 1, 11GND 14 | – |
All parts (10)
CH340G USB to Serial UART Bridge Controller
USB serial converter, UART, SOIC-16
CH340C USB to serial UART bridge
USB to UART bridge with MODEM control signals (RTS#, DTR#, DSR#, DCD#, RI#, CTS#), built-in oscillator interface, 3.3V/5V supply options, SOP-16 package.
CH9102F USB-to-UART Bridge
USB 2.0 full-speed to UART bridge with modem control signals and GPIOs. QFN-24 4x4mm package, 0.5mm pitch, backplane pad listed as pin 0.
CP2102N USB-to-UART Bridge Controller
Silicon Labs USB-to-UART bridge with USB 2.0 full-speed interface, UART flow control, GPIO, USB charger control and suspend outputs. QFN28 pinout.
CP2102N USB to UART Bridge Controller
USB to UART master bridge, QFN-24
CP2104-F03-GMR USB to UART Bridge Controller
USB to UART bridge controller with integrated 5 V regulator, VBUS sense, 4 GPIO, and full RS-232 style modem control signals (RTS/CTS/DTR/DSR/DCD/RI). QFN-24 package.
FT232RL USB to Serial UART Interface IC
USB to Serial Interface, SSOP-28
FT230XS-R USB to Basic UART IC
USB to basic UART bridge IC in 16-pin SSOP. VCC 5V or 3V3, VCCIO 1V8-3V3 for IO, 3V3 output at 50mA, reset and configurable CBUS I/O pins.
FT2232HL Dual High Speed USB to Multipurpose UART/FIFO
Dual-channel high speed USB to multipurpose UART/FIFO IC with RS232 UART, FT245 FIFO, bit-bang, MPSSE and CPU-style FIFO modes. 64-pin LQFP package.
MCP2221A USB-to-UART/I2C Converter
USB-to-UART serial converter with I2C master, four multifunction GP pins (GPIO, ADC, DAC, clock, LED), integrated USB termination and oscillator. Supply 3.3V USB.