DIP-8 and SOIC-8: 8-Pin IC Pinouts
Timers, op-amps, memory, interface chips and regulators in 8-pin packages.
The 8-pin package is the most common IC package of all. As DIP-8 (dual in-line package) with 2.54 mm pitch it fits any breadboard, and as SOIC-8 with 1.27 mm pitch it is the SMD version with an identical pinout. Counting always works the same way: pin 1 is marked by a notch or dot, numbering continues down the same side to pin 4 and comes back up the opposite side from pin 5 to pin 8, counter-clockwise when viewed from the top.
Many 8-pin parts follow the same supply rule: GND on pin 4 and VCC on pin 8, diagonally opposite. That applies to dual op-amps such as the LM358 and TL072, to the 24LC and AT24C EEPROMs, to SPI flash such as the W25Q32 and to the ATtiny85. There are important exceptions, though: the NE555 has GND on pin 1, single op-amps such as the LM741 put V+ on pin 7, and CAN transceivers have GND on pin 2 and VCC on pin 3.
The analysis below shows how many parts follow the most common layout, and the table shows the supply pins of each one. A chip inserted the wrong way round swaps VCC and GND and rarely survives.
Overview from the pinout data
24 of 56 parts have GND on pin 4 and the supply on pin 8.
All parts (56)
NE555 Precision Timer
The classic precision timing circuit capable of producing accurate time delays or oscillation in astable or monostable modes.
LM358 Low-Power Dual Operational Amplifier
Low-Power, Dual Operational Amplifiers, DIP-8/SOIC-8/TO-99-8
LM741 General Purpose Operational Amplifier
Operational Amplifier, DIP-8/TO-99-8
LM393 Dual Differential Comparator
Low-Power, Low-Offset Voltage, Dual Comparators, DIP-8/SOIC-8/TO-99-8
LM311 Voltage Comparator with Strobe
Voltage Comparator, DIP-8/SOIC-8
LM386 Low Voltage Audio Power Amplifier
Low Voltage Audio Power Amplifier, DIP-8/SOIC-8/SSOP-8
TL071 Low-Noise JFET-Input General-Purpose Op-Amp
Single Low-Noise JFET-Input Operational Amplifiers, DIP-8/SOIC-8
TL072 Low-Noise JFET-Input Dual Op-Amp
Dual Low-Noise JFET-Input Operational Amplifiers, DIP-8/SOIC-8
NE5532 Dual High-Performance Low-Noise Op-Amp
Dual Low-Noise Operational Amplifiers, DIP-8/SOIC-8
OP07 Ultra-Low Offset Voltage Operational Amplifier
Very low input offset voltage (75µV max) operational amplifier with low drift and high open-loop gain (300V/mV), making it the classic standard for precision instrumentation.
CA3140 4.5MHz BiMOS Operational Amplifier with MOSFET Input
BiMOS operational amplifier combining high-voltage PMOS transistors with high-voltage bipolar transistors on a single monolithic chip. Features 1.5 TΩ input impedance and rail-to-rail output swing.
OPA2134 SoundPlus High Performance Audio Op-Amp
Dual SoundPlus High Performance Audio Operational Amplifiers, DIP-8/SOIC-8
OPA1612 Dual SoundPlus Audio Op Amp
Dual bipolar-input audio op amp. 1.1 nV/sqrt(Hz) noise at 1 kHz, 0.000015% THD+N at 1 kHz, 27 V/us slew rate, 40 MHz bandwidth at G=+1, +-2.25 V to +-18 V supply.
OPA2340UA Dual Rail-to-Rail Operational Amplifier
Dual single-supply rail-to-rail CMOS op amp. 5.5 MHz bandwidth, 6 V/us slew rate, 750 uA/channel quiescent current, 2.7 V to 5.5 V supply, -40 to 125 C specified range.
MCP6002 1MHz Low-Power Rail-to-Rail Dual Op-Amp
1MHz, Low-Power Op Amp, DIP-8
TLV9062IDR Dual Op Amp
Dual operational amplifier, 8-pin SOIC (D) package, from the TLV9061/TLV9062/TLV9064 family. Pin assignments per datasheet SBOS839N Figure 5-6 and Table 5-3.
THS3001 420MHz High-Speed Current-Feedback Amplifier
High-speed current-feedback op amp: 420MHz bandwidth (G=1, -3dB), 6500V/us slew rate, 40ns settling to 0.1%, 100mA output drive, +/-4.5V to +/-16V supply, -96dBc THD at 1MHz.
INA128UA Precision Instrumentation Amplifier
Precision low-power instrumentation amplifier with 50uV max offset, 0.5uV/C max drift, 120dB min CMR, gain 1 to 10000 set by external RG, supply +/-2.25V to +/-18V.
INA333 Micro-Power Zero-Drift Rail-to-Rail Instrumentation Amplifier
Micro-power (50 uA) zero-drift rail-to-rail instrumentation amplifier, 1.8 V to 5.5 V supply, gain 1 to 1000 set by external RG (G = 1 + 100k/RG), RFI filtered inputs.
AD8421 Gain-Set Differential Amplifier
Amplifier with RG gain-set terminals, G = 1 + (9.9 kOhm / RG), REF terminal for output level shift, +VS/-VS supplies. Shown in 8-lead SOIC, MSOP and LFCSP packages.
ATtiny85 8-Bit AVR Microcontroller (DIP-8)
20MHz, 8kB Flash, 512B SRAM, 512B EEPROM, debugWIRE, DIP-8
ATtiny13 8-Bit AVR Microcontroller (DIP-8)
20MHz, 1kB Flash, 64B SRAM, 64B EEPROM, debugWIRE, DIP-8
PIC12F675 8-Pin Flash-Based 8-Bit CMOS Microcontroller
Popular 8-pin CMOS microcontroller with 1.75KB Flash memory, 64 bytes RAM, 128 bytes EEPROM, 4-channel 10-bit ADC, internal 4MHz oscillator, and analog comparator.
24LC16B 16Kb I2C Serial EEPROM
I2C Serial EEPROM, 16Kb (2048 x 8), 2.5–5.5V, DIP-8/SOIC-8/TSSOP-8. Address pins A0–A2 are No Connect (NC), block addressing is handled internally via the I2C address byte.
24LC256 256Kb I2C Compatible 2-Wire Serial EEPROM
I2C Serial EEPROM, 256Kb (32768 x 8), 2.5–5.5V, DIP-8/SOIC-8/TSSOP-8/DFN-8. Up to 8 devices on one bus via A0–A2 address pins.
AT24C32 32-Kbit I2C Serial EEPROM
32-Kbit (4096 x 8) serial I2C EEPROM with hardware write protection, 32-byte page write, and 1 million write endurance. Commonly paired with DS3231 RTC modules.
AT24C256C I2C Serial EEPROM 256Kbit
256-Kbit two-wire serial EEPROM, 32,768 x 8, I2C interface, 1.7V to 5.5V (Grade 3) or 2.5V to 5.5V (Grade 1), hardware write-protect, 3 address inputs.
25LC256 / 25LCxxx SPI Serial EEPROM Family
SPI Serial EEPROM family (25LC010A–25LC1024), 1.8–5.5V, DIP-8/SOIC-8/TSSOP-8. Pinout identical across the family.
MB85RS64V Serial FeRAM Memory with SPI Interface
Serial FeRAM memory with SPI-compatible interface (CS, SCK, SI, SO), write protect and hold pins. 8-pin plastic SOP 150mil package.
W25Q32JV 32Mbit SPI NOR Flash Memory
3V, 32M-bit (4M-byte) Serial NOR Flash memory with dual/quad SPI, used for external firmware/data storage on ESP32, Arduino and FPGA boards.
W25Q64JVSSIQ 64Mbit Serial NOR Flash (SPI/Dual/Quad)
64Mbit serial NOR flash with Standard, Dual and Quad SPI interface, 8-pin SOIC 208-mil package.
W25Q80DVSNIG 8Mbit Serial Flash Memory with Dual/Quad SPI
8M-bit serial flash memory with standard, dual and quad SPI interface in 8-pin SOIC 150-mil package (code SN).
MX25L6433F Serial Flash Memory
64M-bit serial Flash memory with SPI, dual I/O and quad I/O support, +3.0V supply. Pin list from the 8-pin SOP (200mil) package in the datasheet.
DS1307 64 x 8 Serial Real-Time Clock (I2C)
64 x 8, Serial, I2C Real-time clock, 4.5V to 5.5V VCC, 0°C to +70°C, DIP-8
DS1302 Trickle-Charge Timekeeping RTC
Trickle-charge timekeeping chip containing a real-time clock/calendar and 31 bytes of static RAM. Communicates with microprocessors via a simple 3-wire SPI-like synchronous serial interface (CE, SCLK, I/O) and operates down to 2.0V.
PCF8563 Real-Time Clock/Calendar
Low-power CMOS Real-Time Clock/Calendar with I2C interface, programmable clock output, alarm and timer functions, backed by a 32.768kHz crystal oscillator.
MCP7940N Real-Time Clock/Calendar with SRAM
I2C real-time clock/calendar with SRAM and battery backup input. Uses external 32.768 kHz crystal (6-9 pF load). Open-drain SDA and multifunction MFP outputs.
MCP79410 I2C Real-Time Clock/Calendar with SRAM
I2C real-time clock/calendar (RTCC) with battery backup input and SRAM, driven by an external 32.768 kHz crystal. Pin-compatible family members MCP79411 and MCP79412.
MAX485 Low-Power RS-485 / RS-422 Transceiver
Low-power transceiver for RS-485 and RS-422 communication with one driver and one receiver, supporting data rates up to 2.5 Mbps over differential balanced lines.
MAX31855 Cold-Junction Compensated Thermocouple-to-Digital Converter
Precision thermocouple-to-digital converter with a built-in 14-bit analog-to-digital converter (ADC) and cold-junction compensation. Resolves temperatures from -270°C to +1800°C with 0.25°C resolution via a read-only SPI-compatible interface.
MAX6675 K-Thermocouple-to-Digital Converter
Cold-junction-compensated K-thermocouple-to-digital converter with 12-bit SPI read-only output resolving temperatures from 0°C to +1024°C with 0.25°C resolution.
MCP4921 12-Bit DAC with SPI Interface
Single-channel 12-bit Digital-to-Analog Converter (DAC) with an internal output amplifier and high-speed SPI serial interface (up to 20 MHz). Features user-selectable gain (1x or 2x) and selectable external voltage reference input.
MCP2551 High-Speed CAN Transceiver
High-Speed CAN Transceiver, 1Mbps, 5V supply, DIP-8
MCP2562 CAN Transceiver
CAN transceiver with permanent dominant detection, VDD and VIO undervoltage detection, Standby mode input, and separate VIO supply for RXD (MCP2562 variant).
SN65HVD230 CAN Transceiver
3.3V CAN transceiver with RS mode select (high speed, low power, slope control) and VCC/2 Vref output. Pin 5 and 8 differ on HVD232 (NC).
TJA1051 High-Speed CAN Transceiver
High-Speed CAN Transceiver, silent mode, SOIC-8
ISO1050 isolated CAN transceiver
Isolated CAN transceiver with digital-side VCC1 (3 to 5.5 V) and transceiver-side VCC2 (5 V), CAN bus lines CANH/CANL, and separate GND1/GND2 references. DUB 8-pin package.
MCP2003B LIN Transceiver
LIN bus transceiver with open-drain RXD, TTL TXD and CS inputs, HV-tolerant wake-up input, and VREN regulator enable output. Battery-referenced VBB supply, SOIC-8 package.
ICL7660 Switched-Capacitor Voltage Inverter
Monolithic CMOS switched-capacitor voltage converter that converts a positive input voltage (+1.5V to +10.0V) to an equivalent negative output voltage (-1.5V to -10.0V) with 99.9% conversion efficiency, requiring only two external capacitors.
MC34063A Universal DC-DC Converter Controller
Monolithic DC-DC converter control circuit containing an internal temperature compensated reference, comparator, duty cycle controlled oscillator with active peak current limit circuit, driver and high current output switch (1.5A peak). Capable of Step-Up (Boost), Step-Down (Buck), and Inverting operation.
TPS54331 3-A 28-V Step-Down DC-DC Converter
3-A, 28-V input non-synchronous buck converter with integrated 80-mOhm high-side MOSFET, fixed 570-kHz switching, Eco-mode pulse skipping, and adjustable slow-start.
MP2307DN-LF-Z 3A 23V synchronous step-down converter
3A, 23V input, 340kHz synchronous rectified step-down converter with current-mode control, internal MOSFETs, soft-start and 0.925V feedback reference.
LM2675M-5.0 Simple Switcher 1A Step-Down Voltage Regulator
1A step-down (buck) switching voltage regulator with internal high-side FET, 5.0 V fixed output option, boot-strap capacitor input, feedback pin, and ON/OFF enable. Supply range 6.5 V to 40 V.
AP7361C 1A Low Dropout Adjustable/Fixed Regulator with Enable
1A low dropout linear regulator with enable, adjustable or fixed output (0.8V to 5.0V adjustable), 2.2V to 6.0V input, 60uA typical quiescent current, 1.5A current limit, thermal shutdown.
IR2104STRPBF High-Side/Low-Side Half-Bridge Gate Driver
High voltage, high speed half-bridge driver for N-channel MOSFET/IGBT. Floating high side rated to 600V, 10-20V gate supply, 130/270 mA peak output current, internal deadtime, SOIC-8.
WS2811 3-Channel Constant Current LED Driver IC
3-channel constant-current LED driver IC with single-wire NZR communication protocol. Drives RGB LED strips and pixels with 256 grayscale levels per channel.