Pinouts & Pin-Belegungen
für ICs & Halbleiter.

Pinout-Übersichten für Timer, Operationsverstärker, Logikgatter, Spannungswandler und Treiber-ICs.

Bereits 377+ Bauteile verfügbar

Alle Boards, Chips & Stecker

Entwicklungsplattformen, Mikrocontroller, ICs und Standard-Schnittstellen

Chip
Analog Devices

ADG1408 8:1 analog multiplexer

ADG1408 8-channel analog multiplexer, single drain D, 3-bit address A0-A2 with active high enable EN, dual or single supply operation (VSS/VDD).

Chip
Analog Devices

ADM3053 Isolated CAN Transceiver

Isolated CAN transceiver with iCoupler data isolation and isoPower isolated DC-DC supply. Slope control on RS; standby when RS is high. 20 pins.

Chip
Texas Instruments

ADS1220 24-bit 2-kSPS 4-channel delta-sigma ADC with PGA

24-bit, 2 kSPS, 4-channel delta-sigma ADC with low-noise PGA (gain up to 128), SPI interface, excitation current sources, temperature sensor and internal/external clock.

Chip
Texas Instruments

ADS131M04 4-Channel Delta-Sigma ADC

4-channel analog-to-digital converter with differential analog inputs, serial data interface (SCLK, DIN, DOUT, CS, DRDY), master clock input, and on-chip digital LDO.

Chip
Analog Devices

ADuM1200/ADuM1201 Digital Isolator

Dual-channel digital isolator with reinforced insulation rated 560 VPEAK per IEC 60747-17. Ambient range -40C to +105C, or -40C to +125C for W automotive grades.

Chip
Diodes Inc

AP22802AW5-7 Current-Limited Power Switch

Current-limited load switch with over-current and over-temperature fault flag (open-drain, active low), enable input, SOT-25 package. Not recommended for new design.

Chip
Diodes Inc

AP63203WU-7 3.8V-32V 2A Synchronous Buck Converter

2A synchronous step-down DC/DC buck converter, 3.8V to 32V input, 0.8V +/-1% feedback, integrated 125mOhm high-side and 68mOhm low-side MOSFETs, 1.1MHz, peak current mode control, spread spectrum EMI reduction.

Chip
Diodes Inc

AP7361C 1A Low Dropout Adjustable/Fixed Regulator with Enable

1A low dropout linear regulator with enable, adjustable or fixed output (0.8V to 5.0V adjustable), 2.2V to 6.0V input, 60uA typical quiescent current, 1.5A current limit, thermal shutdown.

Chip
Microchip

AT24C256C I2C Serial EEPROM 256Kbit

256-Kbit two-wire serial EEPROM, 32,768 x 8, I2C interface, 1.7V to 5.5V (Grade 3) or 2.5V to 5.5V (Grade 1), hardware write-protect, 3 address inputs.

Chip
Microchip

ATtiny1614 8-bit AVR microcontroller

8-bit AVR MCU with 16KB Flash, 2KB SRAM, 256B EEPROM, GPIO on VDD power domain, UPDI programming, crystal and external clock inputs. SOIC-14 package.

Chip
Texas Instruments

BQ25895RTWR I2C Single-Cell Li-Ion Battery Charger with Boost

I2C-controlled single-cell Li-ion charger with USB input, MaxCharge D+/D- adapter support, ICO, and 4.5-5.5 V battery boost on PMID up to 3.1 A. WQFN-24 with PowerPAD.

Chip
onsemi

CAT4101 1 A Constant-Current LED Driver with PWM Dimming

1 A constant-current LED sink, 0.5 V dropout at 1 A, LED current set by RSET resistor, PWM dimming via EN/PWM, LED pin up to 25 V, thermal shutdown.

Chip
WCH

CH340C USB to serial UART bridge

USB to UART bridge with MODEM control signals (RTS#, DTR#, DSR#, DCD#, RI#, CTS#), built-in oscillator interface, 3.3V/5V supply options, SOP-16 package.

Chip
WCH

CH9102F USB-to-UART Bridge

USB 2.0 full-speed to UART bridge with modem control signals and GPIOs. QFN-24 4x4mm package, 0.5mm pitch, backplane pad listed as pin 0.

Chip
Silicon Labs

CP2102N USB-to-UART Bridge Controller

Silicon Labs USB-to-UART bridge with USB 2.0 full-speed interface, UART flow control, GPIO, USB charger control and suspend outputs. QFN28 pinout.

Häufige Fragen & Transparenz

Wissenswertes zu Datenquellen, Nutzung und Datenschutz

Woher stammen die Pinout-Daten und Spezifikationen?

Die Pinout-Daten und technischen Angaben basieren auf den Datenblättern der jeweiligen Hersteller sowie frei zugänglichen Dokumentationen und öffentlichen Quellen. Da PinoutDatabase ein unabhängiges Projekt ist, das ich als Einzelperson pflege, gebe ich mein Bestes für hohe Genauigkeit, Fehler können aber natürlich vorkommen.

Darf ich die Grafiken nutzen und wie werden sie erstellt?

Die SVG-Vektordateien und PNG-Grafiken dürfen für private Zwecke frei heruntergeladen und verwendet werden. Die Diagramme erstelle ich je nach Bauteil entweder manuell oder generiere sie automatisiert anhand der jeweiligen Gehäuse-Bauform und Pinbelegung.

Fehler entdeckt oder ein Bauteil fehlt? Wie kann ich Feedback geben?

Feedback aus der Community ist sehr willkommen! Wenn du einen Fehler entdeckst oder ein bestimmtes Bauteil vermisst, nutze einfach den 'Fehler melden'-Button direkt auf der jeweiligen Bauteilseite oder schreibe mir eine Nachricht über das Kontaktformular.

Ist die Nutzung kostenlos und wie steht es um den Datenschutz?

Aktuell ist die Nutzung von PinoutDatabase komplett kostenlos und ohne Registrierung möglich. Alle interaktiven Web-Tools laufen rein clientseitig in deinem Browser. Ausführliche Details zur Datenverarbeitung findest du direkt auf der Datenschutzseite.