Pinouts & Pin-Belegungen
für ICs & Halbleiter.

Pinout-Übersichten für Timer, Operationsverstärker, Logikgatter, Spannungswandler und Treiber-ICs.

Bereits 377+ Bauteile verfügbar

Alle Boards, Chips & Stecker

Entwicklungsplattformen, Mikrocontroller, ICs und Standard-Schnittstellen

Chip
Renesas

ISL78420 Tri-level PWM high/low-side MOSFET gate driver

Synchronous high/low-side NMOS gate driver with tri-level PWM input, adjustable dead time via RDT, bootstrap diode, and VDD/VHB undervoltage protection. -40 to +125C.

Chip
Texas Instruments

ISO1050 isolated CAN transceiver

Isolated CAN transceiver with digital-side VCC1 (3 to 5.5 V) and transceiver-side VCC2 (5 V), CAN bus lines CANH/CANL, and separate GND1/GND2 references. DUB 8-pin package.

Chip
Texas Instruments

LM2675M-5.0 Simple Switcher 1A Step-Down Voltage Regulator

1A step-down (buck) switching voltage regulator with internal high-side FET, 5.0 V fixed output option, boot-strap capacitor input, feedback pin, and ON/OFF enable. Supply range 6.5 V to 40 V.

Chip
Texas Instruments

LM2940IMP-5.0/NOPB 1-A Low Dropout Linear Regulator

1-A positive low dropout linear regulator, 6 V to 26 V input, typical dropout 0.5 V at 1 A, reverse battery protection, short circuit and thermal overload protection.

Chip
Texas Instruments

LP5009 9-channel I2C RGB LED driver

9-channel constant-current sink LED driver with 12-bit 29-kHz PWM per channel, I2C interface, VCC 2.7-5.5 V, up to 35 mA per channel, integrated color mixing and brightness control.

Chip
NXP

LPC1114FBD48/302 32-bit ARM Cortex-M0 microcontroller

32-bit ARM Cortex-M0 MCU, LQFP48 pinout from LPC1113/14 table. GPIO ports 0-3, UART, SPI, I2C, 16/32-bit timers, ADC inputs, JTAG/SWD debug, 3.3 V supply.

Chip
NXP

LPC812M101JDH20 32-bit ARM Cortex-M0+ microcontroller

NXP LPC81xM 32-bit ARM Cortex-M0+ MCU, TSSOP20 package. GPIO, USART, SPI, I2C, SCT, analog comparator, on-chip oscillator, 3.3 V supply.

Chip
Analog Devices

LT3045 Ultralow Noise 500mA LDO Regulator

Ultralow noise, high PSRR 500mA linear regulator with programmable output via SET pin, current limit via ILIM, power good via PG/PGFB, and EN/UV enable. Input 2V to 20V, output 0V to 15V.

Chip
Analog Devices

LT3080 Linear Regulator

Linear regulator with VCONTROL, IN, OUT and SET pins. Absolute max 40V on VCONTROL and IN, Tjmax 125C, indefinite output short-circuit duration. Pin 9 exposed pad is OUT.

Chip
Analog Devices

LTC3622 Dual Step-Down Regulator

Dual synchronous step-down DC/DC regulator with Burst Mode/pulse-skip control, external sync, 180 degree phase select, programmable current limit, and INTVCC LDO. 14-lead DFN.

Chip
Maxim Integrated

MAX17055 1-Cell Fuel Gauge with ModelGauge m5 EZ

7uA 1-cell battery fuel gauge with ModelGauge m5 EZ algorithm, I2C/SMBus-style 2-wire serial interface, ALRT open-drain alert, thermistor bias input and Kelvin sense resistor pins.

Chip
RAMXEED (Fujitsu)

MB85RS64V Serial FeRAM Memory with SPI Interface

Serial FeRAM memory with SPI-compatible interface (CS, SCK, SI, SO), write protect and hold pins. 8-pin plastic SOP 150mil package.

Chip
onsemi

MC74HC595A 8-Bit Shift Register with Latch

8-bit serial-in, parallel-out shift register with storage latch and tri-state outputs. Serial data output SQH for cascading. Logic supply VCC on pin 16, GND on pin 8.

Chip
Microchip

MCP1700 Low Dropout Linear Voltage Regulator

Low dropout linear regulator with 3.3V fixed output (MCP1700T-3302E/TT). Typical 1.6 uA LDO bias current. Requires about 1 uF input capacitance for stable operation.

Chip
Microchip

MCP2003B LIN Transceiver

LIN bus transceiver with open-drain RXD, TTL TXD and CS inputs, HV-tolerant wake-up input, and VREN regulator enable output. Battery-referenced VBB supply, SOIC-8 package.

Häufige Fragen & Transparenz

Wissenswertes zu Datenquellen, Nutzung und Datenschutz

Woher stammen die Pinout-Daten und Spezifikationen?

Die Pinout-Daten und technischen Angaben basieren auf den Datenblättern der jeweiligen Hersteller sowie frei zugänglichen Dokumentationen und öffentlichen Quellen. Da PinoutDatabase ein unabhängiges Projekt ist, das ich als Einzelperson pflege, gebe ich mein Bestes für hohe Genauigkeit, Fehler können aber natürlich vorkommen.

Darf ich die Grafiken nutzen und wie werden sie erstellt?

Die SVG-Vektordateien und PNG-Grafiken dürfen für private Zwecke frei heruntergeladen und verwendet werden. Die Diagramme erstelle ich je nach Bauteil entweder manuell oder generiere sie automatisiert anhand der jeweiligen Gehäuse-Bauform und Pinbelegung.

Fehler entdeckt oder ein Bauteil fehlt? Wie kann ich Feedback geben?

Feedback aus der Community ist sehr willkommen! Wenn du einen Fehler entdeckst oder ein bestimmtes Bauteil vermisst, nutze einfach den 'Fehler melden'-Button direkt auf der jeweiligen Bauteilseite oder schreibe mir eine Nachricht über das Kontaktformular.

Ist die Nutzung kostenlos und wie steht es um den Datenschutz?

Aktuell ist die Nutzung von PinoutDatabase komplett kostenlos und ohne Registrierung möglich. Alle interaktiven Web-Tools laufen rein clientseitig in deinem Browser. Ausführliche Details zur Datenverarbeitung findest du direkt auf der Datenschutzseite.