Pinouts & Pin-Belegungen
für ICs & Halbleiter.
Pinout-Übersichten für Timer, Operationsverstärker, Logikgatter, Spannungswandler und Treiber-ICs.
Alle Boards, Chips & Stecker
Entwicklungsplattformen, Mikrocontroller, ICs und Standard-Schnittstellen
74HC14 Hex Inverting Schmitt Trigger
Six independent Schmitt-trigger inverters in high-speed CMOS. 2–6V supply. Same pin-out as 74HC04 but with hysteresis on each input, making it suitable for noisy or slow-rising signals and oscillator circuits.
74HC165 8-Bit Parallel-In / Serial-Out Shift Register
8-bit parallel-load shift register. Pull ~PL LOW to latch parallel inputs D0–D7; then clock out serially via Q7 (or its complement ~Q7). ~CE (clock enable, Active Low) gates the clock. Commonly chained for reading multiple buttons or sensors over SPI.
74HC193 Synchronous 4-Bit Binary Up/Down Counter
Synchronous 4-bit reversible up/down binary counter with separate Count-Up and Count-Down clocks, asynchronous parallel load (~PL), asynchronous master reset (MR), and cascade outputs.
74HC238 3-to-8 Line Decoder / Demultiplexer
High-speed 3-to-8 line decoder/demultiplexer with active-high outputs (complement of 74HC138) and three enable inputs (two active-low and one active-high).
74HC245 Octal Bus Transceiver with 3-State Outputs
Octal bidirectional bus transceiver with 3-state outputs. DIR controls data direction (HIGH = A→B, LOW = B→A). ~OE (Active Low) disables all outputs to high-impedance. Widely used for 3.3V↔5V level translation.
74HC32 / 74LS32 Quad 2-Input OR Gate
Quad 2-input OR gate. Available in 74LS (low-power Schottky TTL) and 74HC (high-speed CMOS) families, pin-compatible. Output is HIGH when at least one input is HIGH.
74HC393 Dual 4-Bit Binary Ripple Counter
Dual 4-bit binary ripple counter with individual clock (~CP) and master reset (MR) inputs for each 4-bit stage (can be cascaded for 8-bit counting).
74HC4051 8-Channel Analog Multiplexer / Demultiplexer
Single 8-channel bidirectional analog switch (multiplexer/demultiplexer). Address pins S0/S1/S2 select one of 8 channels (Y0–Y7) to connect to the common I/O (Z). ~E disables all switches. VEE allows bipolar analog signals; tie to GND for 0–5V operation.
74HC541 Octal 3-State Non-Inverting Buffer / Line Driver
Octal non-inverting buffer and line driver with 3-state outputs and straight-through flow-through pinout architecture for easy PCB bus routing.
74HC573 Octal Transparent D-Type Latch with 3-State Outputs
Octal transparent D-type latch with 3-state outputs and flow-through pinout architecture, ideal for driving bus lines or memory address latches.
74HC74 Dual D-Type Positive-Edge-Triggered Flip-Flop
Dual positive-edge-triggered D-type flip-flop with asynchronous individual set (~PRE) and clear (~CLR) inputs and complementary Q and ~Q outputs.
74HC86 Quad 2-Input XOR Gate
Quad 2-input exclusive-OR (XOR) gate in high-speed CMOS. 2–6V supply. Output is HIGH when inputs differ. Pin-compatible with 74LS86.
AMS1117-3.3 Low Dropout Voltage Regulator
1A Low Dropout positive fixed 3.3V voltage regulator in surface-mount SOT-223 package with thermal overload and short-circuit current limiting.
AMS1117-5.0 Low Dropout Voltage Regulator
1A Low Dropout positive fixed 5.0V voltage regulator in surface-mount SOT-223 package with internal current limiting and thermal protection.
ATmega32U4 8-Bit Microcontroller with USB (TQFP-44)
16MHz, 32kB Flash, 2.5kB SRAM, 1kB EEPROM, USB 2.0, TQFP-44
Häufige Fragen & Transparenz
Wissenswertes zu Datenquellen, Nutzung und Datenschutz
Woher stammen die Pinout-Daten und Spezifikationen?
Die Pinout-Daten und technischen Angaben basieren auf den Datenblättern der jeweiligen Hersteller sowie frei zugänglichen Dokumentationen und öffentlichen Quellen. Da PinoutDatabase ein unabhängiges Projekt ist, das ich als Einzelperson pflege, gebe ich mein Bestes für hohe Genauigkeit, Fehler können aber natürlich vorkommen.
Darf ich die Grafiken nutzen und wie werden sie erstellt?
Die SVG-Vektordateien und PNG-Grafiken dürfen für private Zwecke frei heruntergeladen und verwendet werden. Die Diagramme erstelle ich je nach Bauteil entweder manuell oder generiere sie automatisiert anhand der jeweiligen Gehäuse-Bauform und Pinbelegung.
Fehler entdeckt oder ein Bauteil fehlt? Wie kann ich Feedback geben?
Feedback aus der Community ist sehr willkommen! Wenn du einen Fehler entdeckst oder ein bestimmtes Bauteil vermisst, nutze einfach den 'Fehler melden'-Button direkt auf der jeweiligen Bauteilseite oder schreibe mir eine Nachricht über das Kontaktformular.
Ist die Nutzung kostenlos und wie steht es um den Datenschutz?
Aktuell ist die Nutzung von PinoutDatabase komplett kostenlos und ohne Registrierung möglich. Alle interaktiven Web-Tools laufen rein clientseitig in deinem Browser. Ausführliche Details zur Datenverarbeitung findest du direkt auf der Datenschutzseite.