USB-Pinbelegung: D+, D−, VBUS und ID
Die USB-Signale von Steckern, Mainboard-Headern, M.2-Steckplätzen und USB-Chips.
USB 2.0 kommt mit vier Leitungen aus: VBUS liefert 5 V, GND ist die Masse, und die Daten laufen differenziell über das Paar D+ und D−. Mini- und Micro-USB haben einen fünften Pin, ID, der bei USB On-The-Go festlegt, ob ein Gerät als Host oder als Peripherie arbeitet. USB 3.0 ergänzt zwei weitere differenzielle Paare für SuperSpeed, lässt das USB-2.0-Paar aber unverändert, damit alte Geräte weiter funktionieren.
Die Tabelle zeigt für jeden Stecker und jedes Bauteil, an welchen Pins D+, D−, VBUS und ID liegen. Neben den gängigen Buchsen findest du den 9-poligen USB-2.0-Header auf PC-Mainboards, die M.2-Steckplätze Key B und Key E, die USB für Modems und WLAN-Karten herausführen, sowie Chips mit eingebautem USB wie den ATmega32U4 und die USB-UART-Wandler CH340G, CP2102N und FT232RL.
D+ und D− müssen als Paar mit 90 Ω differenzieller Impedanz geführt werden. Wer die beiden Leitungen vertauscht, bekommt keine Verbindung, beschädigt aber nichts. Ein Klick auf ein Bauteil öffnet das vollständige Pinout.
USB-Pins je Bauteil
| Bauteil | D+ | D− | VBUS | ID |
|---|---|---|---|---|
| USB Type-B Standard 4-Pin InterfaceUSB Implementers Forum (USB-IF) | 3 · D+ | 2 · D- | 1 · VBUS | – |
| Mini-USB Type-B 5-Pin InterfaceUSB-IF (USB Implementers Forum) | 3 · D+ | 2 · D- | 1 · VBUS | 4 · ID |
| Micro-USB Type-B 5-Pin InterfaceUSB-IF (USB Implementers Forum) | 3 · D+ | 2 · D- | 1 · VBUS | 4 · ID |
| Micro-USB 3.0 Type-B (10-Pin)USB Implementers Forum (USB-IF) | 3 · D+ | 2 · D- | 1 · VBUS | 4 · ID |
| USB 3.0 Type-A SuperSpeed InterfaceUSB-IF (USB Implementers Forum) | 3 · D+ | 2 · D- | 1 · VBUS | – |
| USB 2.0 Internal 9-Pin Motherboard HeaderIntel / USB-IF | 5 · USB1_D+6 · USB2_D+ | 3 · USB1_D-4 · USB2_D- | – | – |
| Apple Lightning ConnectorApple Inc. | 2 · L0p6 · L1p | 3 · L0n7 · L1n | – | – |
| M.2 (NGFF) Key B Connector (WWAN & SATA SSD)PCI-SIG | 7 · USB_D+ | 9 · USB_D- | – | – |
| M.2 (NGFF) Key E Connector (Wi-Fi & Bluetooth)PCI-SIG | 3 · USB_D+ | 5 · USB_D- | – | – |
| ATmega32U4 8-Bit Microcontroller with USB (TQFP-44)Microchip / Atmel | 4 · D+ | 3 · D- | 7 · VBUS | – |
| CH340G USB to Serial UART Bridge ControllerWCH (Jiangsu Qinheng) | 5 · UD+ | 6 · UD- | – | – |
| CP2102N USB to UART Bridge ControllerSilicon Labs | 3 · D+ | 4 · D- | 8 · VBUS | – |
| FT232RL USB to Serial UART Interface ICFTDI Chip | 15 · USBD+ | 16 · USBD- | – | – |
Pin-Nummer · Pin-Name. „+n“ = weitere Pins mit derselben Funktion.
Alle Bauteile (13)
USB Type-B Standard 4-Pin Interface
Standard 4-pin square USB Type-B female/male connector interface for printers, Arduino Uno, USB audio interfaces, and external peripheral devices.
Mini-USB Type-B 5-Pin Interface
Compact 5-pin USB 2.0 connector commonly found on older digital cameras, GPS devices, MP3 players, and game controllers. Succeeded by Micro-USB.
Micro-USB Type-B 5-Pin Interface
Compact 5-pin USB 2.0 connector with dedicated OTG ID pin for dynamic host/device mode negotiation.
Micro-USB 3.0 Type-B (10-Pin)
10-pin SuperSpeed USB 3.0 Micro-B connector combining a standard 5-pin USB 2.0 section with an additional 5-pin SuperSpeed section, commonly found on portable external hard drives.
USB 3.0 Type-A SuperSpeed Interface
Standard 9-pin USB connector with blue color coding. Fully backward compatible with USB 2.0 (pins 1-4) with 5 additional SuperSpeed differential and ground lines (pins 5-9).
USB 2.0 Internal 9-Pin Motherboard Header
Standard 9-pin (2x5 keyed) internal motherboard header supporting dual USB 2.0 front panel ports with +5V VBUS, Data- (D-), Data+ (D+), and Ground (GND).
Apple Lightning Connector
Proprietary 8-pin reversible connector used for Apple iOS devices (iPhone, iPad, iPod) carrying power (VBUS), high-speed differential USB data, and accessory control signals.
M.2 (NGFF) Key B Connector (WWAN & SATA SSD)
Standard 75-position M.2 Key B edge connector interface (notch at pins 12-19) providing PCIe x2, SATA, USB 2.0/3.0, and SIM card (UIM) signals for cellular modems and legacy SATA SSDs.
M.2 (NGFF) Key E Connector (Wi-Fi & Bluetooth)
Standard 75-position M.2 Key E edge connector interface (notch at pins 24-31) providing PCIe x1, USB 2.0, SDIO, UART, and I2S/PCM for wireless networking (Wi-Fi & Bluetooth) and CNVi companion modules.
ATmega32U4 8-Bit Microcontroller with USB (TQFP-44)
16MHz, 32kB Flash, 2.5kB SRAM, 1kB EEPROM, USB 2.0, TQFP-44
CH340G USB to Serial UART Bridge Controller
USB serial converter, UART, SOIC-16
CP2102N USB to UART Bridge Controller
USB to UART master bridge, QFN-24
FT232RL USB to Serial UART Interface IC
USB to Serial Interface, SSOP-28