Microchip & Atmel: Pinouts von AVR, PIC und MCP-Chips
Mikrocontroller, Speicher, Wandler, Port-Expander und CAN-Bausteine von Microchip Technology.
Microchip Technology aus Arizona ist vor allem für seine PIC-Mikrocontroller bekannt. 2016 übernahm Microchip den Konkurrenten Atmel und damit die AVR-Familie, auf der die klassischen Arduino-Boards beruhen: ATmega328P im Uno und Nano, ATmega2560 im Mega, ATmega32U4 im Leonardo und die kleinen ATtiny-Typen. Deshalb tragen manche Bauteile hier noch den Namen Atmel im Datenblatt.
Neben den Controllern liefert Microchip viele Peripherie-Chips mit dem Präfix MCP, die in Maker-Projekten ständig auftauchen: die Port-Expander MCP23017 (I2C) und MCP23S17 (SPI), der 8-Kanal-ADC MCP3008, die DACs MCP4725 und MCP4921, die rail-to-rail-fähigen Operationsverstärker MCP6002 und MCP6004, der CAN-Controller MCP2515 mit den Transceivern MCP2551 und MCP2562 sowie der Li-Ion-Lader MCP73831. Dazu kommen serielle EEPROMs der Reihen 24LC, 25LC und AT24C.
Die Tabelle zeigt Gehäuse, Versorgungspins und Schnittstellen aller Microchip- und Atmel-Bauteile in der Datenbank. Viele davon gibt es als DIP und als SOIC mit gleicher Belegung, sodass sich ein Aufbau auf dem Steckbrett später ohne Änderung der Verdrahtung auf eine SMD-Platine übertragen lässt.
Übersicht aus den Pinout-Daten
Alle Bauteile (40)
ATmega328P 8-Bit AVR Microcontroller (DIP-28)
20MHz, 32kB Flash, 2kB SRAM, 1kB EEPROM, DIP-28
ATmega328P 8-Bit AVR Microcontroller
High performance, low power 8-bit AVR RISC-based microcontroller with 32KB flash, standard on Arduino Nano and Uno.
ATmega8 28-Pin 8-Bit AVR Microcontroller
Classic 28-pin AVR RISC microcontroller with 8KB Flash, 1KB SRAM, 512 bytes EEPROM, 6-channel 10-bit ADC, USART, SPI, I2C (TWI), and 3 PWM channels. Original MCU of the Arduino NG/Severino.
ATmega16 40-Pin 8-Bit AVR Microcontroller
40-pin high-performance low-power 8-bit AVR microcontroller with 16KB In-System Programmable Flash, 1KB SRAM, 512 bytes EEPROM, 8-channel 10-bit ADC, JTAG interface, and 32 I/O lines.
ATmega32 40-Pin 8-Bit AVR Microcontroller
40-pin AVR microcontroller with 32KB In-System Programmable Flash, 2KB SRAM, 1KB EEPROM, 8-channel 10-bit ADC, JTAG interface, hardware multiplier, and 32 I/O lines.
ATmega32U4 8-Bit Microcontroller with USB (TQFP-44)
16MHz, 32kB Flash, 2.5kB SRAM, 1kB EEPROM, USB 2.0, TQFP-44
ATtiny13 8-Bit AVR Microcontroller (DIP-8)
20MHz, 1kB Flash, 64B SRAM, 64B EEPROM, debugWIRE, DIP-8
ATtiny85 8-Bit AVR Microcontroller (DIP-8)
20MHz, 8kB Flash, 512B SRAM, 512B EEPROM, debugWIRE, DIP-8
ATtiny84 8-Bit AVR Microcontroller (DIP-14)
20MHz, 8kB Flash, 512B SRAM, 512B EEPROM, debugWIRE, DIP-14
ATtiny2313 20-Pin 8-Bit AVR Microcontroller
20-pin low-power CMOS 8-bit AVR microcontroller with 2KB In-System Programmable Flash, 128 bytes EEPROM, 128 bytes SRAM, full duplex USART, and SPI master/slave.
ATtiny1614 8-bit AVR microcontroller
8-bit AVR MCU with 16KB Flash, 2KB SRAM, 256B EEPROM, GPIO on VDD power domain, UPDI programming, crystal and external clock inputs. SOIC-14 package.
PIC12F675 8-Pin Flash-Based 8-Bit CMOS Microcontroller
Popular 8-pin CMOS microcontroller with 1.75KB Flash memory, 64 bytes RAM, 128 bytes EEPROM, 4-channel 10-bit ADC, internal 4MHz oscillator, and analog comparator.
PIC16F84A 8-Bit Flash Microcontroller (DIP-18)
PIC16F84A, 1K Flash, 68B SRAM, 64B EEPROM, DIP18
PIC16F628A 8-Bit Flash Microcontroller (DIP-18)
2048W Flash, 224B SRAM, 128B EEPROM, DIP18
PIC16F886 28-Pin Flash Microcontroller with nanoWatt (DIP-28)
8K Flash, 256B SRAM, 256B EEPROM, XLP, DIP28
PIC18F2550 28-Pin High-Performance USB Microcontroller
28-pin high-performance USB 2.0 Full-Speed microcontroller with 32KB Flash, 2048 bytes RAM, 256 bytes EEPROM, 10-bit ADC, CCP/PWM, and nanoWatt power management.
PIC18F4550 40-Pin High-Performance USB Microcontroller
40-pin flagship USB 2.0 microcontroller with 32KB Flash, 2048 bytes RAM, 256 bytes EEPROM, 13-channel 10-bit ADC, Streaming Parallel Port (SPP), and hardware USB transceiver.
24LC16B 16Kb I2C Serial EEPROM
I2C Serial EEPROM, 16Kb (2048 x 8), 2.5–5.5V, DIP-8/SOIC-8/TSSOP-8. Address pins A0–A2 are No Connect (NC), block addressing is handled internally via the I2C address byte.
24LC256 256Kb I2C Compatible 2-Wire Serial EEPROM
I2C Serial EEPROM, 256Kb (32768 x 8), 2.5–5.5V, DIP-8/SOIC-8/TSSOP-8/DFN-8. Up to 8 devices on one bus via A0–A2 address pins.
AT24C32 32-Kbit I2C Serial EEPROM
32-Kbit (4096 x 8) serial I2C EEPROM with hardware write protection, 32-byte page write, and 1 million write endurance. Commonly paired with DS3231 RTC modules.
AT24C256C I2C Serial EEPROM 256Kbit
256-Kbit two-wire serial EEPROM, 32,768 x 8, I2C interface, 1.7V to 5.5V (Grade 3) or 2.5V to 5.5V (Grade 1), hardware write-protect, 3 address inputs.
24AA02E48 I2C Serial EEPROM
2-wire I2C serial EEPROM, 1.7V to 5.5V supply. Open-drain SDA bidirectional data pin requires pull-up to VCC; SCL serial clock input.
25LC256 / 25LCxxx SPI Serial EEPROM Family
SPI Serial EEPROM family (25LC010A–25LC1024), 1.8–5.5V, DIP-8/SOIC-8/TSSOP-8. Pinout identical across the family.
MCP23017 16-Bit I/O Expander with I2C Interface
16-bit general purpose parallel I/O port expander with high-speed I2C interface (up to 1.7 MHz), configurable interrupt output pins, and 100k internal pull-ups.
MCP23S17 16-Bit I/O Expander with SPI Interface
16-bit general purpose parallel I/O port expander with high-speed 10 MHz SPI interface, hardware address pins for sharing the same SPI bus, and interrupt outputs.
MCP3008 8-Channel 10-Bit ADC with SPI Interface
Popular 8-channel 10-bit analog-to-digital converter (ADC) with SPI serial interface, 200 ksps sampling rate at 5V, and programmable pseudo-differential inputs.
MCP4725 12-Bit DAC with I2C Interface and EEPROM
Low-power, high accuracy, single channel, 12-bit voltage output Digital-to-Analog Converter (DAC) with integrated non-volatile EEPROM and 2-wire I2C interface. Stores power-on reset output settings directly in on-board EEPROM.
MCP4921 12-Bit DAC with SPI Interface
Single-channel 12-bit Digital-to-Analog Converter (DAC) with an internal output amplifier and high-speed SPI serial interface (up to 20 MHz). Features user-selectable gain (1x or 2x) and selectable external voltage reference input.
MCP6002 1MHz Low-Power Rail-to-Rail Dual Op-Amp
1MHz, Low-Power Op Amp, DIP-8
MCP6004 1MHz Low-Power Rail-to-Rail Quad Op-Amp
1MHz, Low-Power Op Amp, DIP-14/SOIC-14/TSSOP-14
MCP2515 Stand-Alone CAN Controller with SPI Interface
Stand-Alone CAN Controller with SPI Interface, SOIC-18
MCP2518FD CAN FD Controller with SPI Interface
External CAN FD controller with SPI interface, TXCAN/RXCAN to transceiver, oscillator pins, two interrupt/GPIO pins and CLKO/SOF output.
MCP2551 High-Speed CAN Transceiver
High-Speed CAN Transceiver, 1Mbps, 5V supply, DIP-8
MCP2562 CAN Transceiver
CAN transceiver with permanent dominant detection, VDD and VIO undervoltage detection, Standby mode input, and separate VIO supply for RXD (MCP2562 variant).
MCP2003B LIN Transceiver
LIN bus transceiver with open-drain RXD, TTL TXD and CS inputs, HV-tolerant wake-up input, and VREN regulator enable output. Battery-referenced VBB supply, SOIC-8 package.
MCP2221A USB-to-UART/I2C Converter
USB-to-UART serial converter with I2C master, four multifunction GP pins (GPIO, ADC, DAC, clock, LED), integrated USB termination and oscillator. Supply 3.3V USB.
MCP7940N Real-Time Clock/Calendar with SRAM
I2C real-time clock/calendar with SRAM and battery backup input. Uses external 32.768 kHz crystal (6-9 pF load). Open-drain SDA and multifunction MFP outputs.
MCP79410 I2C Real-Time Clock/Calendar with SRAM
I2C real-time clock/calendar (RTCC) with battery backup input and SRAM, driven by an external 32.768 kHz crystal. Pin-compatible family members MCP79411 and MCP79412.
MCP1700 Low Dropout Linear Voltage Regulator
Low dropout linear regulator with 3.3V fixed output (MCP1700T-3302E/TT). Typical 1.6 uA LDO bias current. Requires about 1 uF input capacitance for stable operation.
MCP73831 Li-Ion Battery Charge Controller
Single-cell Li-Ion/Li-Po battery management controller with constant current/constant voltage charging, programmable charge current via PROG resistor, and charge status output.