Bauteilfamilie

74HC-Logik: Pinouts von Gattern, Registern und Multiplexern

Die wichtigsten Bausteine der 74HC- und 74LS-Familie mit Gehäuse, Versorgungspins und Datenblatt.

Die 74er-Reihe ist die bekannteste Familie digitaler Logikbausteine. Die Nummer hinter „74“ bestimmt die Funktion, die Buchstaben davor die Technologie: 74LS ist bipolare TTL-Logik für 5 V, 74HC ist CMOS und arbeitet von 2 V bis 6 V bei deutlich geringerer Stromaufnahme, 74HCT ist CMOS mit TTL-kompatiblen Eingängen. Ein 74HC00 und ein 74LS00 haben deshalb dieselbe Pinbelegung, auch wenn sie elektrisch verschieden sind.

Die Familie reicht von einfachen Gattern (74HC00 NAND, 74HC04 Inverter, 74HC14 Schmitt-Trigger) über Flip-Flops und Zähler bis zu Schieberegistern wie dem 74HC595, mit dem ein Mikrocontroller über drei Leitungen acht zusätzliche Ausgänge bekommt. Dazu kommen Decoder (74HC138), analoge Multiplexer (74HC4051) und Bus-Treiber (74HC245).

Die Tabelle zeigt einen festen Rhythmus: Bei 14-poligen Bausteinen liegt GND fast immer an Pin 7 und VCC an Pin 14, bei 16-poligen an Pin 8 und 16, bei 20-poligen an Pin 10 und 20. Ausnahmen wie der 74HC4052 haben einen zusätzlichen Pin für eine negative Versorgung. Unbenutzte CMOS-Eingänge nie offen lassen, sondern auf GND oder VCC legen.

Übersicht aus den Pinout-Daten

12 von 33 Bauteilen haben GND an Pin 7 und die Versorgung an Pin 14.

BauteilHerstellerGehäusePinsVersorgung
74HC00 Quad 2-Input NAND GateTexas Instruments14-Pin DIP / SOIC14VCC 14GND 7
74HC02 Quad 2-Input NOR GateTexas Instruments / Nexperia / onsemi14-Pin DIP / SOIC14VCC 14GND 7
74HC04 Hex InverterTexas Instruments14-Pin DIP / SOIC14VCC 14GND 7
74HC08 Quad 2-Input AND GateTexas Instruments / Nexperia / onsemi14-Pin DIP / SOIC14VCC 14GND 7
74HC08 / 74LS08 Quad 2-Input AND GateTexas Instruments14-Pin DIP / SOIC14VCC 14GND 7
74HC32 / 74LS32 Quad 2-Input OR GateTexas Instruments14-Pin DIP / SOIC14VCC 14GND 7
74HC86 Quad 2-Input XOR GateTexas Instruments14-Pin DIP / SOIC14VCC 14GND 7
74HC14 Hex Inverting Schmitt TriggerTexas Instruments14-Pin DIP / SOIC14VCC 14GND 7
74HC125 Quad 3-State Non-Inverting BufferTexas Instruments / Nexperia14-Pin DIP / SOIC14VCC 14GND 7
74HC74 Dual D-Type Positive-Edge-Triggered Flip-FlopTexas Instruments / Nexperia14-Pin DIP / SOIC14VCC 14GND 7
74HC164 8-Bit Serial-In / Parallel-Out Shift RegisterTexas Instruments / Nexperia / onsemi14-Pin DIP / SOIC14VCC 14GND 7
74HC165 8-Bit Parallel-In / Serial-Out Shift RegisterTexas Instruments16-Pin DIP / SOIC16VCC 16GND 8
74HC595 8-Bit Serial-In / Parallel-Out Shift RegisterTexas Instruments / Nexperia16-Pin DIP / SOIC16VCC 16GND 8
MC74HC595A 8-Bit Shift Register with Latchonsemi16-Pin DIP / SOIC16VCC 16GND 8
74HC138 3-to-8 Line Decoder / DemultiplexerTexas Instruments16-Pin DIP / SOIC16VCC 16GND 8
74HC139 Dual 2-to-4 Line Decoder/DemultiplexerTexas Instruments16-Pin DIP / SOIC16VCC 16GND 8
74HC238 3-to-8 Line Decoder / DemultiplexerTexas Instruments / Nexperia16-Pin DIP / SOIC16VCC 16GND 8
74HC151 8-Input Data Selector / MultiplexerTexas Instruments16-Pin DIP / SOIC16VCC 16GND 8
74HC153 Dual 4-to-1 Line Data Selector/MultiplexerTexas Instruments16-Pin DIP / SOIC16VCC 16GND 8
74HC157 Quad 2-Line to 1-Line Data Selector/MultiplexerTexas Instruments16-Pin DIP / SOIC16VCC 16GND 8
74HC161 Synchronous 4-Bit Binary Counter (Asynchronous Clear)Texas Instruments16-Pin DIP / SOIC16VCC 16GND 8
74HC193 Synchronous 4-Bit Binary Up/Down CounterTexas Instruments / Nexperia16-Pin DIP / SOIC16VCC 16GND 8
74HC393 Dual 4-Bit Binary Ripple CounterTexas Instruments / Nexperia14-Pin DIP / SOIC14VCC 14GND 7
74HC4051 8-Channel Analog Multiplexer / DemultiplexerTexas Instruments / Nexperia16-Pin DIP / SOIC16VCC 16GND 8
74HC4052 Dual 4-Channel Analog Multiplexer / DemultiplexerNXP Semiconductors16-Pin DIP / SOIC16VCC 16GND 7, 8
74HC4053 Triple 2-Channel Analog Multiplexer / DemultiplexerNXP Semiconductors16-Pin DIP / SOIC16VCC 16GND 7, 8
CD74HC4067 16-Channel Analog Multiplexer/DemultiplexerTexas Instruments / NXP24-Pin DIP / SOIC24VCC 24GND 12
74HC244 Octal Buffer/Line Driver with 3-State OutputsTexas Instruments20-Pin DIP / SOIC20VCC 20GND 10
74HC245 Octal Bus Transceiver with 3-State OutputsTexas Instruments20-Pin DIP / SOIC20VCC 20GND 10
74HC373 Octal Transparent D-Type Latch with 3-State OutputsTexas Instruments20-Pin DIP / SOIC20VCC 20GND 10
74HC374 Octal Edge-Triggered D-Type Flip-Flop with 3-State OutputsTexas Instruments20-Pin DIP / SOIC20VCC 20GND 10
74HC541 Octal 3-State Non-Inverting Buffer / Line DriverTexas Instruments / Nexperia20-Pin DIP / SOIC20VCC 20GND 10
74HC573 Octal Transparent D-Type Latch with 3-State OutputsTexas Instruments / Nexperia20-Pin DIP / SOIC20VCC 20GND 10

Alle Bauteile (33)

Chip
Texas Instruments

74HC00 Quad 2-Input NAND Gate

Quad 2-input NAND gate in high-speed CMOS logic. 2–6V supply. Each gate output is the inverted AND of its two inputs. Pin-compatible with 74LS00 and CD4011B.

Chip
Texas Instruments / Nexperia / onsemi

74HC02 Quad 2-Input NOR Gate

High-speed CMOS quad 2-input NOR gate with output drive capability of 10 LSTTL loads. Operating voltage 2V to 6V.

Chip
Texas Instruments

74HC04 Hex Inverter

Six independent single-input inverter gates in high-speed CMOS logic. 2–6V supply. Each gate output is the logic complement of its input. Pin-compatible with 74LS04.

Chip
Texas Instruments / Nexperia / onsemi

74HC08 Quad 2-Input AND Gate

High-speed CMOS quad 2-input AND gate. Pin-compatible upgrade to 74LS08 with lower power consumption and wider voltage range (2V to 6V).

Chip
Texas Instruments

74HC08 / 74LS08 Quad 2-Input AND Gate

Quad 2-input AND gate. Available in 74LS (low-power Schottky TTL) and 74HC (high-speed CMOS) families, pin-compatible. Output is HIGH only when both inputs are HIGH.

Chip
Texas Instruments

74HC32 / 74LS32 Quad 2-Input OR Gate

Quad 2-input OR gate. Available in 74LS (low-power Schottky TTL) and 74HC (high-speed CMOS) families, pin-compatible. Output is HIGH when at least one input is HIGH.

Chip
Texas Instruments

74HC86 Quad 2-Input XOR Gate

Quad 2-input exclusive-OR (XOR) gate in high-speed CMOS. 2–6V supply. Output is HIGH when inputs differ. Pin-compatible with 74LS86.

Chip
Texas Instruments

74HC14 Hex Inverting Schmitt Trigger

Six independent Schmitt-trigger inverters in high-speed CMOS. 2–6V supply. Same pin-out as 74HC04 but with hysteresis on each input, making it suitable for noisy or slow-rising signals and oscillator circuits.

Chip
Texas Instruments / Nexperia

74HC125 Quad 3-State Non-Inverting Buffer

Quadruple bus buffer gates with independent active-low output enables (~OE), frequently used for bus multiplexing and SPI chip-select isolation.

Chip
Texas Instruments / Nexperia

74HC74 Dual D-Type Positive-Edge-Triggered Flip-Flop

Dual positive-edge-triggered D-type flip-flop with asynchronous individual set (~PRE) and clear (~CLR) inputs and complementary Q and ~Q outputs.

Chip
Texas Instruments / Nexperia / onsemi

74HC164 8-Bit Serial-In / Parallel-Out Shift Register

High-speed CMOS 8-bit serial-in parallel-out shift register with two AND-gated serial inputs and asynchronous master reset. No output latch (unlike 74HC595).

Chip
Texas Instruments

74HC165 8-Bit Parallel-In / Serial-Out Shift Register

8-bit parallel-load shift register. Pull ~PL LOW to latch parallel inputs D0–D7; then clock out serially via Q7 (or its complement ~Q7). ~CE (clock enable, Active Low) gates the clock. Commonly chained for reading multiple buttons or sensors over SPI.

Chip
Texas Instruments / Nexperia

74HC595 8-Bit Serial-In / Parallel-Out Shift Register

8-bit serial-input / parallel-output shift register with 3-state outputs. Data is clocked in serially on SRCLK, then latched to the output pins on a rising edge of RCLK. Commonly chained for expanding digital outputs over SPI.

Chip
onsemi

MC74HC595A 8-Bit Shift Register with Latch

8-bit serial-in, parallel-out shift register with storage latch and tri-state outputs. Serial data output SQH for cascading. Logic supply VCC on pin 16, GND on pin 8.

Chip
Texas Instruments

74HC138 3-to-8 Line Decoder / Demultiplexer

3-to-8 line decoder with active-low outputs. Three enable inputs (two active-low ~G2A/~G2B, one active-high G1) allow easy cascading. Complement of 74HC238 (active-high outputs).

Chip
Texas Instruments

74HC139 Dual 2-to-4 Line Decoder/Demultiplexer

High-speed silicon-gate CMOS dual 2-to-4 line decoder/demultiplexer. Features active-low enable inputs and active-low decoded outputs. Ideal for memory address decoding.

Chip
Texas Instruments / Nexperia

74HC238 3-to-8 Line Decoder / Demultiplexer

High-speed 3-to-8 line decoder/demultiplexer with active-high outputs (complement of 74HC138) and three enable inputs (two active-low and one active-high).

Chip
Texas Instruments

74HC151 8-Input Data Selector / Multiplexer

High-speed silicon-gate CMOS 8-channel data selector/multiplexer. Decodes 3 binary address inputs (S0, S1, S2) to select one of eight data sources (D0 through D7) with complementary true (Y) and inverted (~W) outputs.

Chip
Texas Instruments

74HC153 Dual 4-to-1 Line Data Selector/Multiplexer

Dual 4-line to 1-line data selector/multiplexer with common select inputs and separate active-low enable inputs for each section.

Chip
Texas Instruments

74HC157 Quad 2-Line to 1-Line Data Selector/Multiplexer

Quad 2-line to 1-line multiplexer with non-inverting outputs, common select input, and common active-low strobe/enable.

Chip
Texas Instruments

74HC161 Synchronous 4-Bit Binary Counter (Asynchronous Clear)

Synchronous presettable 4-bit binary counter with asynchronous master reset, look-ahead carry outputs, and synchronous parallel loading.

Chip
Texas Instruments / Nexperia

74HC193 Synchronous 4-Bit Binary Up/Down Counter

Synchronous 4-bit reversible up/down binary counter with separate Count-Up and Count-Down clocks, asynchronous parallel load (~PL), asynchronous master reset (MR), and cascade outputs.

Chip
Texas Instruments / Nexperia

74HC393 Dual 4-Bit Binary Ripple Counter

Dual 4-bit binary ripple counter with individual clock (~CP) and master reset (MR) inputs for each 4-bit stage (can be cascaded for 8-bit counting).

Chip
Texas Instruments / Nexperia

74HC4051 8-Channel Analog Multiplexer / Demultiplexer

Single 8-channel bidirectional analog switch (multiplexer/demultiplexer). Address pins S0/S1/S2 select one of 8 channels (Y0–Y7) to connect to the common I/O (Z). ~E disables all switches. VEE allows bipolar analog signals; tie to GND for 0–5V operation.

Chip
NXP Semiconductors

74HC4052 Dual 4-Channel Analog Multiplexer / Demultiplexer

Dual 4-channel analog multiplexer/demultiplexer with common channel select logic and active-low enable. Supports bidirectional signal routing of digital and analog voltages up to 10V with low ON resistance and break-before-make switching.

Chip
NXP Semiconductors

74HC4053 Triple 2-Channel Analog Multiplexer / Demultiplexer

Triple 2-channel analog multiplexer/demultiplexer (three independent SPDT analog switches) with three separate digital select inputs and a common enable input. Designed for analog and digital signal switching up to 10V peak-to-peak.

Chip
Texas Instruments / NXP

CD74HC4067 16-Channel Analog Multiplexer/Demultiplexer

High-speed CMOS 16-channel analog multiplexer/demultiplexer with low on-resistance (typ. 70 Ohm) and wide analog voltage range. Ideal for data acquisition and signal routing.

Chip
Texas Instruments

74HC244 Octal Buffer/Line Driver with 3-State Outputs

Octal non-inverting buffer and line driver designed to drive bus lines or memory address registers. Features two 4-bit sections with independent active-low output enables.

Chip
Texas Instruments

74HC245 Octal Bus Transceiver with 3-State Outputs

Octal bidirectional bus transceiver with 3-state outputs. DIR controls data direction (HIGH = A→B, LOW = B→A). ~OE (Active Low) disables all outputs to high-impedance. Widely used for 3.3V↔5V level translation.

Chip
Texas Instruments

74HC373 Octal Transparent D-Type Latch with 3-State Outputs

Octal transparent D-type latch with 3-state outputs. When Latch Enable (LE) is high, outputs follow inputs. When LE goes low, inputs are latched.

Chip
Texas Instruments

74HC374 Octal Edge-Triggered D-Type Flip-Flop with 3-State Outputs

Octal edge-triggered D-type flip-flop with 3-state true outputs. Data is transferred to outputs on the low-to-high transition of the clock pulse.

Chip
Texas Instruments / Nexperia

74HC541 Octal 3-State Non-Inverting Buffer / Line Driver

Octal non-inverting buffer and line driver with 3-state outputs and straight-through flow-through pinout architecture for easy PCB bus routing.

Chip
Texas Instruments / Nexperia

74HC573 Octal Transparent D-Type Latch with 3-State Outputs

Octal transparent D-type latch with 3-state outputs and flow-through pinout architecture, ideal for driving bus lines or memory address latches.