Die interaktive Datenbank für
Pinouts & Pin-Belegungen.

Interaktive Diagramme, Pin-Funktionen und technische Datenblätter für Mikrocontroller, Entwicklungsboards und ICs auf einen Blick.

Bereits 377+ Bauteile verfügbar

Alle Boards, Chips & Stecker

Entwicklungsplattformen, Mikrocontroller, ICs und Standard-Schnittstellen

Chip
Titan Micro Electronics

TM1637 2-Wire Serial 7-Segment LED Driver Controller

Dedicated LED drive control circuit with keyboard scan interface and 2-wire serial interface (CLK, DIO). Commonly used to drive 4-digit or 6-digit 7-segment clock displays.

Chip
Worldsemi

WS2811 3-Channel Constant Current LED Driver IC

3-channel constant-current LED driver IC with single-wire NZR communication protocol. Drives RGB LED strips and pixels with 256 grayscale levels per channel.

Chip
Exar Corporation

XR-2206 Monolithic Function Generator IC

Monolithic function generator IC capable of producing high-quality sine, square, triangle, ramp, and pulse waveforms of high-stability and accuracy from 0.01 Hz to over 1 MHz.

Chip
Intersil / Harris

CA3140 4.5MHz BiMOS Operational Amplifier with MOSFET Input

BiMOS operational amplifier combining high-voltage PMOS transistors with high-voltage bipolar transistors on a single monolithic chip. Features 1.5 TΩ input impedance and rail-to-rail output swing.

Chip
Texas Instruments

CD40106B CMOS Hex Schmitt-Trigger Inverter

Six independent inverter circuits with Schmitt-trigger input action. The hysteresis provides high noise immunity and clean square-wave outputs from slowly changing analog inputs.

Chip
Texas Instruments

CD4046B CMOS Micropower Phase-Locked Loop (PLL)

Micropower phase-locked loop consisting of a linear voltage-controlled oscillator (VCO) and two different phase comparators with common signal-input and comparator-input.

Chip
Texas Instruments

LM1875 20W Hi-Fi Audio Power Amplifier

Monolithic power amplifier offering very low distortion (0.015% THD) and high-quality performance for consumer audio applications. Capable of delivering 20W into a 4Ω or 8Ω load.

Chip
STMicroelectronics / TI / onsemi

LM7809 9V 1.5A Positive Voltage Regulator

Three-terminal positive linear voltage regulator with fixed 9V output. Capable of supplying over 1.5A output current with internal thermal overload and short-circuit current limiting protection.

Chip
STMicroelectronics / TI / onsemi

LM7815 15V 1.5A Positive Voltage Regulator

Standard 3-terminal positive voltage regulator with fixed 15V output. Commonly used in dual-rail audio equipment and op-amp power supplies in combination with LM7915.

Chip
STMicroelectronics / onsemi / TI

LM7912 -12V 1.5A Negative Voltage Regulator

Three-terminal negative voltage regulator with fixed -12V output. Note: Pinout differs from LM78xx: Pin 1 is Ground, Pin 2 is Input, and the heatsink tab is connected to Input.

Chip
Analog Devices / TI

OP07 Ultra-Low Offset Voltage Operational Amplifier

Very low input offset voltage (75µV max) operational amplifier with low drift and high open-loop gain (300V/mV), making it the classic standard for precision instrumentation.

Chip
STMicroelectronics / onsemi

TIP31C 100V 3A NPN Power Transistor

Medium-power epitaxial-base NPN silicon transistor in TO-220 package. Designed for general-purpose switching and amplifier applications. Complementary to TIP32C.

Chip
STMicroelectronics / onsemi

TIP32C 100V 3A PNP Power Transistor

Medium-power epitaxial-base PNP silicon transistor in TO-220 package. Designed for general-purpose switching and amplifier applications. Complementary to TIP31C.

Chip
Texas Instruments

74HC244 Octal Buffer/Line Driver with 3-State Outputs

Octal non-inverting buffer and line driver designed to drive bus lines or memory address registers. Features two 4-bit sections with independent active-low output enables.

Chip
Texas Instruments

74HC373 Octal Transparent D-Type Latch with 3-State Outputs

Octal transparent D-type latch with 3-state outputs. When Latch Enable (LE) is high, outputs follow inputs. When LE goes low, inputs are latched.

Häufige Fragen & Transparenz

Wissenswertes zu Datenquellen, Nutzung und Datenschutz

Woher stammen die Pinout-Daten und Spezifikationen?

Die Pinout-Daten und technischen Angaben basieren auf den Datenblättern der jeweiligen Hersteller sowie frei zugänglichen Dokumentationen und öffentlichen Quellen. Da PinoutDatabase ein unabhängiges Projekt ist, das ich als Einzelperson pflege, gebe ich mein Bestes für hohe Genauigkeit, Fehler können aber natürlich vorkommen.

Darf ich die Grafiken nutzen und wie werden sie erstellt?

Die SVG-Vektordateien und PNG-Grafiken dürfen für private Zwecke frei heruntergeladen und verwendet werden. Die Diagramme erstelle ich je nach Bauteil entweder manuell oder generiere sie automatisiert anhand der jeweiligen Gehäuse-Bauform und Pinbelegung.

Fehler entdeckt oder ein Bauteil fehlt? Wie kann ich Feedback geben?

Feedback aus der Community ist sehr willkommen! Wenn du einen Fehler entdeckst oder ein bestimmtes Bauteil vermisst, nutze einfach den 'Fehler melden'-Button direkt auf der jeweiligen Bauteilseite oder schreibe mir eine Nachricht über das Kontaktformular.

Ist die Nutzung kostenlos und wie steht es um den Datenschutz?

Aktuell ist die Nutzung von PinoutDatabase komplett kostenlos und ohne Registrierung möglich. Alle interaktiven Web-Tools laufen rein clientseitig in deinem Browser. Ausführliche Details zur Datenverarbeitung findest du direkt auf der Datenschutzseite.