# MAX7219 8-Digit LED Display Driver

- **Manufacturer**: Maxim Integrated / Analog Devices
- **Type**: Chip
- **Year**: 1996
- **URL (German)**: https://pinoutdb.org/component/max7219
- **URL (English)**: https://pinoutdb.org/en/component/max7219
- **Description**: Compact, serial input/output common-cathode display driver interfacing microprocessors to 7-segment numeric LED displays up to 8 digits, bar-graph displays, or 64 individual LEDs.
- **Datasheets & Links**:
  - [Maxim MAX7219 / MAX7221 Datasheet (PDF)](https://www.analog.com/media/en/technical-documentation/data-sheets/MAX7219-MAX7221.pdf) (datasheet)
  - [LedControl Arduino Library](https://github.com/wayoda/LedControl) (github)

## View: DIP-24 Top View (Package: dip)

| Pin | Signal Name | Type | Alternative Functions / Description |
| :--- | :--- | :--- | :--- |
| 1 | DIN | Digital | Serial Data Input — data latched on CLK rising edge; MSB first; 16-bit word (address + data) [SPI] |
| 2 | DIG 0 | Digital | Digit 0 Common Cathode Driver — sinks current from digit 0 LED cathodes; LOW selects digit [Output] |
| 3 | DIG 4 | Digital | Digit 4 Common Cathode Driver — sinks current from digit 4 LED cathodes; LOW selects digit [Output] |
| 4 | GND | Ground | Ground (0V) — connect both GND pins to ground plane [Ground] |
| 5 | DIG 6 | Digital | Digit 6 Common Cathode Driver — sinks current from digit 6 LED cathodes; LOW selects digit [Output] |
| 6 | DIG 2 | Digital | Digit 2 Common Cathode Driver — sinks current from digit 2 LED cathodes; LOW selects digit [Output] |
| 7 | DIG 3 | Digital | Digit 3 Common Cathode Driver — sinks current from digit 3 LED cathodes; LOW selects digit [Output] |
| 8 | DIG 7 | Digital | Digit 7 Common Cathode Driver — sinks current from digit 7 LED cathodes; LOW selects digit [Output] |
| 9 | GND | Ground | Ground (0V) — connect both GND pins to ground plane [Ground] |
| 10 | DIG 5 | Digital | Digit 5 Common Cathode Driver — sinks current from digit 5 LED cathodes; LOW selects digit [Output] |
| 11 | DIG 1 | Digital | Digit 1 Common Cathode Driver — sinks current from digit 1 LED cathodes; LOW selects digit [Output] |
| 12 | LOAD | Digital | Load / Chip Select (LOAD on MAX7219) — rising edge latches last 16 bits into registers; equivalent to ~CS (Active Low) on MAX7221 [SPI] |
| 13 | CLK | Digital | Serial Clock Input (max 10MHz) — DIN sampled on rising edge; DOUT shifts on falling edge [SPI] |
| 14 | SEG A | Digital | Segment A Anode Driver — sources current to segment A of all digit positions; HIGH = segment ON [Output] |
| 15 | SEG F | Digital | Segment F Anode Driver — sources current to segment F of all digit positions; HIGH = segment ON [Output] |
| 16 | SEG B | Digital | Segment B Anode Driver — sources current to segment B of all digit positions; HIGH = segment ON [Output] |
| 17 | SEG G | Digital | Segment G Anode Driver — sources current to segment G of all digit positions; HIGH = segment ON [Output] |
| 18 | ISET | Analog | Peak Segment Current Set — connect resistor between ISET and V+ to set LED drive current; R_ISET = (V+ − 1.5V) / (I_seg / 100); typical: 9.53kΩ for 40mA peak [Analog] |
| 19 | V+ | Power | Positive Supply Voltage (+4.0V to +5.5V; add 100nF + 10µF bypass caps to GND near pin) [Power] |
| 20 | SEG C | Digital | Segment C Anode Driver — sources current to segment C of all digit positions; HIGH = segment ON [Output] |
| 21 | SEG E | Digital | Segment E Anode Driver — sources current to segment E of all digit positions; HIGH = segment ON [Output] |
| 22 | SEG DP | Digital | Decimal Point Anode Driver — sources current to decimal point segment of all digit positions; HIGH = DP ON [Output] |
| 23 | SEG D | Digital | Segment D Anode Driver — sources current to segment D of all digit positions; HIGH = segment ON [Output] |
| 24 | DOUT | Digital | Serial Data Output — connects to DIN of next MAX7219 for daisy-chaining multiple devices; data propagates with 16.5 CLK cycle delay [SPI] |


---
Source: PinoutDatabase (https://pinoutdb.org). Verify against the manufacturer datasheet before production use.
